background image

3e.  The owner shall not be charged for diagnostic labor which leads to the determination 

that a part covered by the ECS Warranty is in fact defective, provided that such 
diagnostic work is performed at a CPE Authorized Service Outlet.

3f.  CPE shall pay for covered emissions warranty repairs at non-authorized service 

outlets under the following circumstances:

i. The service is required in a population center with a population over 100,000 

according to U.S. Census 2000 without a CPE Authorized Service Outlet AND

ii. The service is required more than 100 miles from a CPE Authorized Service Outlet. 

The 100 mile limitation does not apply in the following states: Alaska, Arizona, 
Colorado, Hawaii, Idaho, Montana, Nebraska, Nevada, New Mexico, Oregon, Texas, 
Utah and Wyoming.

3g. CPE shall be liable for damages to other original engine components or approved 

modifications proximately caused by a failure under warranty of an emission-related 
part covered by the ECS Warranty.

3h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted 

emission-related parts sufficient to meet the expected demand for such emission-
related parts.

3i.  Any CPE Authorized and approved emission-related replacement part may be used 

in the performance of any ECS Warranty maintenance or repair and will be provided 
without charge to the owner. Such use shall not reduce CPE’s warranty obligation.

3j.  Unapproved add-on or modified parts may not be used to modify or repair a CPE 

engine. Such use voids this ECS Warranty and shall be sufficient grounds for 
disallowing an ECS Warranty claim. CPE shall not be liable hereunder for failures of 
any warranted parts of a CPE engine caused by the use of such an unapproved add-
on or modified part. 

Summary of Contents for 055-0216-8































































Reviews: