background image

3

559802 - Masport 4/6 Burner 210 Series - May 2015

Location

• Do not use indoors. Barbecue units are designed for OUTDOOR 

USE ONLY.

• Use in a weather-protected area, preferably under shelter.
• Ensure that the barbecue is on an even and secure surface before 

operating. Use the castor locks if fitted to lock the wheels in 
place.

• Do not use within one metre of any flammable surface of 

structure.

Burn awareness

• Parts of the barbecue do get extremely hot and could cause 

serious burns – touch test the surface before applying a firm grip.

• The hood handle can become hot! The use of cooking gloves and 

long sleeves are advised.

• If cooking with the hood closed, be very careful opening the hood, 

a sudden rush of hot air could burn an unprotected arm.

Gas awareness

• Ensure all gas couplings and hoses are in good condition and 

have been correctly fitted.

• Leak test all gas lines and connections before use.
• Do not store flammable materials near this barbecue.
• Do not place the gas bottle underneath the barbecue directly.
• Do not store spare LPG cylinders under or near this barbecue.
• Do not place or use aerosols near this barbecue.
• Do not store or use gasoline or other flammable vapours or liquids 

in the vicinity of this barbecue.

• Ensure that the gas is turned OFF at the cylinder after use and 

while the barbecue is unattended.

• When turning off the barbecue, shut off the gas at the supply 

source before turning off all the burner controls. 
 

• Do not store gas cylinders below ground level. ULPG is heavier 

than air. Should a leak occur, the gas will collect and could ignite 
due to presence of a flame or electric spark.

For your safety and others

If you smell gas:
Shut off the gas supply to the barbecue.
Extinguish any open flame (candles, cigarettes, etc.)
Clear the area to allow the unburned gas to dissipate.
Be aware of the reason for the gas smell, address this before 
continuing. Should the gas odour come from the LPG cylinder, 
immediately contact the fire department from an elevated safe 
distance.
Connecting the gas cylinder to the barbecue, refer to that section in 
the manual.
Leak testing, refer to that section in the manual.

Safety Equipment

When cooking with oil/grease, fire extinguishing materials should be 
readily accessible.
In the event of an oil/grease fire do not attempt to extinguish with 
water or alcohol. Use type BC dry chemical fire extinguisher or 
smother the fire with dirt, sand or baking soda.

Rain Hazard 

In the event of rain while cooking with oil/grease, turn off the gas 
supply and all burners, cover the barbecue as soon as possible. 
Move people/animals away from around the barbecue.  Do not 
attempt to move the barbecue until it has cooled and can safely be 
moved.

Installation

This Cooking Appliance is 

For Outdoor Use Only 

and 

shall not be used in a building, garage or any other enclosed 
area.

Note!

 

Read carefully the pages containing the parts and 
assembly before assembling your gas grill.
 

The location for your grill

Do not use your gas grill in garages, porches, breezeways, sheds 
or other enclosed areas. Your gas grill is to be used outdoor only, at 
least 43cm from the back and side to any combustible surface. The 
grill should not be placed under any surface that will burn. Do not 
obstruct the flow of combustion and ventilation air around the grill 
housing. Keep this barbecue away from any flammable materials!
(Refer to page 16)

Gas and Regulator Information

Gas grills are used safely by millions of people when following 
simple safety precautions. This barbecue is designed for ULPG 
use only. Bottle size of 4.5kg or greater is recommended for use 
with this barbecue. The regulator must have an outlet pressure of 
2.75kPa. You must have the correct regulator and bottle for the 
barbecue to operate safely and efficiently. The items used in the fuel 
system are designed for operation with the grill. (See parts list for 
replacement items).

Natural Gas conversion option - refer to page 15

Warranty

Refer to the warranty supplied with this BBQ. Should any part fail 
due to defective workmanship or faulty materials within the specified 
period from the date of purchase, Masport will replace or repair the 
defective part free of charge. Refer to the warranty for details. Do 
not use a BBQ that is unsafe.

LPG cylinder 

The cylinder manufacturer/distributor is responsible for the safety 
and performance of the LPG cylinder. This is not included in the 
Masport BBQ warranty. Do not use a cylinder that is unsafe.

Disposal of Packaging

Remove all protective packaging including any protective film from 
stainless steel surfaces.
Make sure you properly dispose of, or recycle the packaging 
material where possible to comply with applicable waste disposal 
laws in your area.

Summary of Contents for AMBASSADOR 80.40RBW 210

































Reviews: