10
timber beams or on encased, rounded roof
parapets.
*
Caution:
In case of the use of fastenings with fall energy
absorbers, it is to be ensured that the maximum
length of 2 m is not exceeded (fast fall
energy absorber 1.5 m + stitched web in the
back-reception eyelet 0.5 m). If guided-type fall
arresters are employed, the snap hook must be
hooked directly into the reception eyelet (D-ring).
Also in case of fastenings with fall energy
absorbers with length 2 m, the snap hook must
be placed directly into the reception eyelet.
3.3 Use of the rear reception eyelet in
Var. BFD 3 with fixed sewn-on fastenings
with integrated tear /
fall-energy absorber
(Type BFD 3)
*
Caution:
In this implementation, max.
admissible total weight (rated
load) of the person 100 KG
In case of the implementation
of Var. BFD, a fastening with
tear / fall-energy absorber
Type BFD 3, with a maximum length of 2 m, has
been fixed sewn into the rear reception eyelet.
This fastening with tear / fall-energy absorber
must not be extended or manipulated.
The snap hook at the end of the fastening is
attached directly to the anchor point.
As an Appendix to these directions for use, the
direction for use
Fastening with integrated tear / fall energy
absorber, tested according to EN 354/355
is additionally delivered. The use references are
to be considered in particular in this case!
If guided-type fall arresters are employed, the
snap hook must be hooked directly into the
reception eyelet (D-ring). It is basically
prohibited to attach the stitched fastening with
tear / fall-energy absorber to the guided-type fall
arrester (danger through overlong fall paths).
3.4 Use of the side hold eyelets
The two side hold eyelets may be employed only
for the work positioning (hold function), where
the fastening for safety belts, according to EN
358, is basically to be attached with a 2-rope
connection and adjusted tightly, so that any free
fall of the user is excluded. The anchor point in
the hold function must be located above the
waist. Furthermore, the fastening for the safety
belt must be held tightly and free movement is to
be limited to 0.60 m. The adjusting devices and
connecting elements are to be checked regularly
during the performance of work.
Important:
If pocket webs / pocket eyelets are sewn on at
the back, these are permissible only for holding
a tool pouch or a tool bag. In no case should a
fastening or similar be attached here.
Any abuse of the side hold eyelets through
hanging or seating in the belt unavoidably
leads to damage and is therefore
inadmissible.
3.5 Use of the ride-up protection eyelet
*
Caution:
In this implementation, max. admissible total
weight (rated load) of the person 100 KG
The full body harnesses in the variants with the
designation "S" are equipped with a ride-up
protection eyelet at the abdominal belt, and
therefore can also be employed in connection
with a guided-type fall arrester, according to EN
353-1.
In this case, it is to be ensured that the ride-
up protection eyelet (D-ring) is always
located centrally in front on the stomach.
4. Cleaning and testing
After completion of work, the equipment should
be cleaned of any contamination. This increases
the service life duration of this type of PPE, as
well as increasing your security. Clean with
warm water at 30°C and fabric-sensitive
detergent and then dry in the shade. Clean belts
have a longer service life. Rub metal fittings
regularly with an oily cloth (e.g. WD 40).
5. Storage
Storage should be implemented in dry
conditions in a sealed metal suitcase or PVC
bag (aerated and protected against direct solar
radiation).
6. Verification
If doubts should exist regarding safe use, or if
the equipment has been stressed through a fall
from a height, the overall equipment must be
withdrawn from use immediately. A PPE
stressed by a fall from a height may be used
again only following written approval from an
expert agency. Regular verification may be
implemented through an expert agency only,
subject to precise observation of the directions
of the manufacturer. Personal Protective
Equipment (PPE) against fall from a height is to
be checked by competent professionals as
required, however at least once within twelve
months. The manufacturer is considered an
expert agency. Also the identification on the
product is to be checked for legibility.
The rear reception eyelet
(D-ring with back plate) should
always be at shoulder height
and the breast belt should rest
centrally on the breast.
Important:
Become familiar with the function of the full body
harness before first use.
In this case, put on the full body harness as
described above and, as a trial, attach at ground
level with fastening (e.g. safety rope). Load the
belt through body weight; leg loops must
enclose the thighs trouble-free. Hanging in the
belt should usually not cause any difficulties,
otherwise check the belt adjustment. With the
loading of the full body harness, the webbing
settles into the respective hardware parts and
any yielding of the webbing is thus minimized.
3. Notes on use
*
Any labeling or identification of this
equipment with a solution-content
Textmaker/Edding on supporting webbing or
ropes is forbidden, since the textile woven
fabric can be damaged by that.
*
This equipment may be used only within
the in-service conditions as stipulated and the
planned intended purpose.
*
The use of this equipment is permitted to
instructed and expert persons only, or use is
subject to direct expert monitoring.
*
There must be no health problems
present (alcohol, drugs, medication, heart or
circulation problems).
*
Furthermore, it must be considered
before the use of this equipment how a possibly
necessary rescue can be realized safely
(emergency - rescue plan).
*
Personal Protective Equipment against
fall from a height should be made available to
the user in person.
*
Before every use, test the overall
Personal Protective Equipment against fall from
a height and do not use damaged devices
(function test).
For your own safety, have it
checked by from another person whether your
full body harness is adjusted correctly.
*
In case of utilization in a fall arrest
system (EN363), always note that there is
sufficient open space below the user.
*
Limit possible fall paths to a minimum
through guided-type fall arresters and similar.
*
Note the correct composition of the
overall PPE, since incorrect combinations of
equipment parts with regard to each other
(compatibility) can impair secure functioning.
Changes or extensions may not be carried out
without prior written approval from the
manufacturer. In the same way, all repairs may
be carried out only in agreement with the
manufacturer.
*
Do not expose to acids, oils or corrosive
chemicals, and if this is unavoidable rinse off
immediately after use and have equipment
tested by an expert.
*
Protect against sharp-edged objects.
*
Textiles are to be protected against heat
higher than 60°C. Attention is to be paid to
melting of the webbing. Weld bead markers are
also to be considered as melting.
*
Avoid any corrosion danger and extreme
heat and cold.
Anchor point:
The anchor point according to EN 795 (minimum
strength 10 kN) is to be selected (as far as
possible above the head) so that free fall and
the fall height is limited to a minimum. The max.
angle to the vertical should never exceed 30° in
this case (swinging).
3.1 Use of the reception eyelet
(Identification A)
The reception eyelet is determined exclusively
for use with a fall arrest system according to EN
363 e.g.:
In combination with the following:
¾
Fastenings with fall energy absorber EN
354/355
¾
Retractable-type fall arresters EN 360
¾
Guided-type fall arresters EN 353-2
¾
Abseiling and rescue devices EN 341 and
1496
3.2 Use of the rear reception eyelet in the
Var. B 3 as a back eyelet extension:
In the implementation Var. B3, full
body harness is provided with a
fastenings of Type Band B3 with a
maximum fastening length of 0.5 m.
This fastening is fixed-sewn on at the
back-reception eyelet and is used to
facilitate operation of this back-
reception eyelet (e.g. in case of
utilization with retractable-type fall arresters).
The Type Band B3 webbing employed here has
been tested successfully over an edge. A steel
edge with radius R = 0.5 mm, without burr, was
employed in this case. Based on this test, the
equipment in corresponding composition is
suitable for use over similar edges (inquire with
the manufacturer about this), such as exist for
example on rolled-steel profile sections, on
20962_MAS 30 + 60_neu.indd 10
10.12.14 09:59
