background image

 Safety 

information 

 

Safety information 

The following symbols are used to identify important safety information: 

 

 

 

 

 

 

 

 

 

Caution! Safety 

hazard. Risk of 

personal injury. 

Caution! Burn 

hazard. Hot 

surface. Do not 

touch. 

Danger! 

Hazardous 

voltage. Contact 

will cause electric 

shock. 

Caution! Fire 

hazard. 

 

 

 

 

 
 

 

 
Warning! This product is not for household use. It presents risks of injury due to 
electric shock, burns, falls and respiratory problems! 

Read this manual before operating the machine, follow the safety precautions 
listed below, and observe all warnings in this manual and printed on the 
machine. Use the system only as described in this manual and in accordance 

with local laws and regulations. 
 
If you have questions about how to operate the machine safely, or if you have 
followed the instructions in this manual and the machine is malfunctioning, 
please contact Martin Service. 

 

Preventing electric shocks 

 

Always ground (earth) the machine electrically. 

 

Use only a source of AC power that complies with local building and 

electrical codes, and that has both overload and ground-fault protection. 

 

Before connecting the Magnum smoke machine to power, check that 

the voltage indicated on the machine’s serial label matches your local 
AC power voltage. If your AC power voltage does not match, do not use 
the machine. Contact Martin Service for assistance. 

 

Before using the machine, check that all power distribution equipment 

and cables are in perfect condition and rated for the current 

requirements of all connected devices. 

 

If the machine or any cables connected to it are in any way damaged, 

defective, wet, or show signs of overheating, stop using the machine 
and contact Martin Service for assistance. 

 

Disconnect the machine from AC power before servicing and when not 

in use. 

 

This system is not waterproof and should not be exposed to wet 

outdoor conditions. Do not immerse in water or any other liquid. Do not 
expose to high-pressure water jets. 

 

Do not spill fluid over or inside the machine. If fluid is spilled, disconnect 

AC power and clean with a damp cloth. If fluid is spilled onto electronic 

parts, take the system out of service and contact Martin for advice. 

 

Do not remove the covers or attempt to repair a faulty machine. Refer 

any service not described in this manual to Martin. 

Summary of Contents for Magnum 650






















Reviews: