24
Exterior 1200 Wash user manual
5. Data cable can be connected either via screw terminals on removable connectors or
via RJ-45 connectors.
See Figure 11. Either connect the data cable
to the luminaire’s
Data 1 DMX IN
screw
terminals (
A
) as follows:
- Connect shield to the terminal marked
- Connect cold (-) to the terminal marked -
- Connect hot (+) to the terminal
or install an RJ-45 connector on the data
cable respecting the pinout listed under "
on page 23 and insert the
connector into the
DMX IN
RJ-45 socket (
B
).
6. Depending on whether the luminaire is the
last one on the link or whether the data link
needs to be continued to another luminaire,
follow one of the following two procedures:
• If the luminaire is the last one on a branch
of the data link, use a pair of long-nosed
pliers to move the DMX termination
jumpers from the
Data set 1
pins (
C
)
marked
OFF
to the pins marked
ON
. This
places a resistance across data hot and
cold to terminate the data link. Ensure that
the termination resistance matches the
type of cable used by setting the
Cable
impedance
jumpers (
D
) to either
100
if
using CAT5 cable for the data link, or
120
if using standard DMX cable.
• If you need to continue the data link to another luminaire, leave the termination
jumpers at
OFF
. Pass the data output cable into the luminaire using another cable
gland as described above. Connect to the luminaire’s
Data 1 DMX OUT
terminals
(
E
) or RJ-45
DMX OUT
socket (
F
), respecting the same pinouts as for the data input
cable.
7. If using shielded CAT5 cable, connect the cable shield to PCB ground (earth) by
routing the cable under the clamp (
G
), folding back the cable shield and tightening the
clamp so that it makes good contact with the shield. .
8. If the power cable has not already been connected, you can connect it now (see
3.2.2: Connecting to AC power"
on page 20). Otherwise reinstall the rear cover plate
as described in "
3.1.4: Connections compartment access"
9. Route the data output cable to the data input of the next luminaire, and continue
connecting up to a total of 32 luminaires, output to input, as described above.
Add an optically isolated amplifier/splitter into the link if you intend to add more than 32
luminaires or branch the link.
The Data 2 connections are reserved for future use.
Data
2
Data
1
Termination
Termination
Data
set 2
set 2
Data
set 1
set 1
50
60
277
250
240
230
220
208
200
DMX
OUT
MAINS
MAIN
FUSE
PCB
Hz
Hz Setting
Volt Setting
Live 2
Fuse
Live 1
Fuse
Ground
Neutral
Live
1
Live
2
50
60
277
250
240
230
220
208
200
Hz Setting
Volt Setting
Service
RJ45
DMX
IN
Cable
impedance
100
120
Data
2
Data
1
Termination
Termination
Data
set 2
set 2
Data
set 1
set 1
50
60
277
250
240
230
220
208
200
DMX
OUT
MAINS
MAIN
FUSE
PCB
Hz
Hz Setting
Volt Setting
Live 2
Fuse
Live 1
Fuse
Ground
Neutral
Live
1
Live
2
50
60
277
250
240
230
220
208
200
Hz Setting
Volt Setting
Service
RJ45
DMX
IN
Cable
impedance
100
120
Figure 11: DMX
connections
A
B
C
D
F
E
G
B
G
Summary of Contents for Exterior 1200 Wash
