INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Before you begin installing, servicing, or maintenance of this product, follow these general precautions.
•
For commercial installation:
service and maintenance of this product should be performed by a qualified, licensed electrician.
•
For residential installation:
If you are unsure about the installation or maintenance of this product, consult a qualified
licensed electrician.
• Do not mount the unit against flammable surfaces.
• This product is intended to be used outdoors, and be subject to the elements; such as rain and snow and we recommend it
to be mounted at least 6’ 6” off the ground
• This LED product must be powered directly to a switched circuit. (on/off).
• This product should not be used in areas with limited ventilation or high ambient temperatures.
• This product CAN NOT be used with a dimmer switch, motion or occupancy sensor or other electronic switching device.
• This product is intended to be connected to a properly installed and grounded UL listed junction box.
WARNING: RISK OF ELECTRICAL SHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring product to the power supply.
• Verify voltage is 110V-240V before installing.
• Make all electrical and grounded connections in accordance with the National Electric Code and any applicable local code
requirements and All wiring connections should be capped with UL listed wire connectors.
CAUTION: RISK OF PRODUCT DAMAGE
• Never connect fixture with power on.
• Avoid covering LED products with insulation, foam, or other materials that will prevent convection or conduction cooling.
• Never connect an LED product directly to dimmer packs, occupancy sensors, timing devices, or other related control devices,
unless individual product specifications deem otherwise.
• LED products are polarity sensitive, ensure proper polarity before installation.
• Do not touch the individual electronic components, it may cause ESD (Electronic Discharge), shorten lamp life
or alter performance.
CAUTION: RISK OF INJURY
• Avoid direct eye exposure to the light source while it is on.
• Let it cool completely before handling.
INSTALLATION INSTRUCTIONS
PART DESCRIPTION
QUANTITY
A
Light Fixture
1
B
Plastic Screw Cover
1
C
Stainless Steel Screw
1
D
Gasket (optional)
1
E
Cross Bar
1
F
Grounding Screw
1
G
Grounding Wire
1
H
Wire Nut
3
I
Stainless Steel Mounting Screws
2
Silicon Sealant recommended (not included)
Tools Required for Installation:
Phillips screwdriver, level
LED MOTION SENSOR SECURITY LIGHT
Item: 4-80053 / 4-80054
PRODUCT SPECIFICATIONS
• Detection Method: PIR (Passive Infrared)
• Detection Range: Max.70ft
• Detection Angle: Up to 240°
• LED Angle: 120°
• Time Adjustment: (minimum) 5 seconds to 1, 5, 12 minutes
• Operating Voltage: 110 ~240 volts 50Hz/60Hz
• IP Rating: 44
Note : Sensor has a 1 1/2 minute warm up period before it will detect motion. when first turned on, wait 1 1/2 minutes.
TROUBLESHOOTING GUIDE
PRODUCT MAINTENANCE
To clean the surface of the light, use mild soap and water.
Do not use scouring pads, powders, steel wool or any other abrasive materials. Do not immerse in water.
SYMPTOM
POSSIBLE CAUSE
Lights will not come on
1. Light switch is turned off.
2. Light is loose or burned out.
3. Fuse is blown or circuit breaker is turned off.
4. Daylight turnoff is in effect (recheck after dark).
5. Incorrect circuit wiring, if this is a new installation.
6. Re-aim the sensor to cover desired area
Lights come on in day light.
Light control may be installed in a relatively dark location.
Lights come on for
no apparent reason.
Light control may be sensing small animals
or automobile traffic (re-aim sensor).
Range is set too high. (Reduce Range setting).
Lights stay on continuously.
1. A lamp is positioned too close to the sensor or pointed
at nearby objects that cause heat to trigger the sensor.
(Reposition the lamp away from the sensor or
nearby objects).
2. Reduce sensitivity.
Lights flash on and off.
1. Heat or light from the lamps may be turning the light
control on and off. (Reposition the lamps away from
the sensor).
2. Heat being reflected from other objects may be affecting
the sensor. (Reposition sensor).
