background image

STEP 3

INSTALLING THE CONTROL BOX ASSEMBLY  

Fasten

 the control box to the wall about 5' (1520) from the ground with screws. 

The holes are in the corner pillars, which are outside the water resistant gasket of 
the control box. See Figures 1, 24  Because the push button is mounted in the 
control box lid, the control box should be mounted within sight of the garage door, 
clear of all moving garage door parts.

ATTENTION! 

 The control box is water resistant.  Do not drill holes in the control 

box!  

Route all wires through the conduit outlets at the bottom of the control 

box.

  Dress wiring tight and straight, using ties, staples or other means.  

See Figures 23, 24

Temporarily fasten

 the control box lid to the left or right side, above or below the 

control box to prevent it from hanging by the push button wires during the setup 
process.  See Figures 23, 24   The push button should only be used when the 
garage door area is free of people or any obstructions.  

Plug

 the three wire low voltage DC motor wiring harness, if not plugged in, into the 

terminal block at the bottom right hand side of the circuit board that is marked "DC 
Motor".  See Figures 10b, 26a, 26b.  Plug the opposite end into the three way 
terminal in the motor assembly. See Figures 2b, 27. Do not cut or shorten excess 
wiring. Coil excess wire and tie away from moving parts. 
See Figure 28

FIGURE 25

COPYRIGHT © 2008 MARTIN DOOR

FIGURE 28

FIGURE 23

FIGURE 24

10

FIGURE 27

FIGURE 26a

FIGURE 26b

Summary of Contents for DC4600





















Reviews: