RIGHT LIGHT LENS
FIGURE 12A
STEP 6
LIGHT BULBS AND LIGHT LENSES
STEP 7
Twist
Position
light bulb(s) (not included
into light bulb sockets.
light lens tabs with corresponding slots in power head and chassis and snap
into place. Two screws are also furnished to fasten bottom part of DC3700e light lenses
ee Figure 12A or 12B
), maximum 60W,
.
S
PHOTO EYES SAFETY SYSTEM
For Martin DC2500e, DC3700e, DC3700e-H
Do not attempt to install Martin DC2500e-O, DC3700e-O (no
photo-eye openers), on any door except the approved, U.L. Listed Martin garage door
and opener system. Attempting to do so will void the U.L. Listing and warranty of the
opener.
Connecting Wires to Photo Eye:
Remove
Open
Push
Place
Mounting the Photo Eyes directly to Wall:
Locate
Using
Repeat
Mounting the Photo Eyes to Brackets:
Locate
Using
Attach
Align
Photo
Slightly
Tighten
about 1/2”(13) of insulation from the ends of the white and black striped photo eye wiring.
the cover flap in the bottom of the photo eye.
wire ends directly into terminal holes. To remove wiring, depress the terminal “tabs” and pull
wiring out. See
the wires in the slot on the right side of the cover flap and close. See
the mounting position 3” to 5” (76 to 127) above the floor for maximum protection.
the round-head screws, secure the photo eye to the wall. See
for the other photo eye. Use shims to align. See page 21
the mounting position 3” to 5” (76 to 127) above the floor. Brackets can be mounted in any
position as long as photo eye beam will have a clear path from one side of door to the other side. Do
not touch vertical tracks because they move as door opens and closes.
the round-head screws provided, fasten the bracket to the wall. See
the photo eye cap and the photo eye cap fastener to the bracket. Attach the photo eye to the
bracket with the fastening wheel. See
photo eyes, so they face each other before tightening fastening wheels. See
eyes maintain an invisible, unbroken beam between each other. When the photo eyes are
connected to the power head and the power is on, the green light on the transmitter photo eye will
illuminate. When the photo eyes are aligned, the red light on the receiver photo eye will illuminate.
loosen the fastening wheel on each photo eye. Rotate the photo eye in the photo eye cap or
slide it in the adjustment area of the bracket until eyes are aligned and the red light on the receiver
photo eye illuminates. See
the transmitter fastening wheel only when you are sure the photo eyes are center point
aligned. See page 21
WARNING:
RISK OF ENTRAPMENT.
FIGURE 13
FIGURE 13
FIGURE 14
FIGURE 15
FIGURE 15
FIGURE 33
FIGURE 33 and page 21
CHASSIS
LIGHT BULB
LIGHT BULB
SOCKET
LIGHT BULB
LEFT
LIGHT LENS
POWER
HEAD
FIGURE 13
FIGURE 14
LIGHT BULB
LIGHT
LENS
CHAIN RAIL
ASSEMBLY ONLY
POWER HEAD
FIGURE 12B
DC3700e
DC2500e
BEL
T
RAIL
ASSEMBL
Y
ONL
Y
COPYRIGHT © 2007 MARTIN DOOR
SLOT
TAB
TAB
SLOT
SLOT
TAB
SLOT
TAB
TAB
CHASSIS
SLOT
TAB
SLOT
Cover Flap
Terminal / Tabs
Wirings to Powerhead
Fastening
Wheel
Lens
Green or Red Light
Terminal Holes
(Receiver or
Transmitter Mark)
To Terminal 1
To Terminal 2
TX or RX
3” to 5”
(76 to 127)
from floor
Round-head
Screw
10
Photo Eye Cap
Photo Eye Cap
Fastener
Fastening Wheel
Photo Eye
Round-Head Screw
Jamb
Mounting Bracket
FIGURE 15
Sun Shield Should only be Installed on Receiver
