manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Installation Manual

Share
Download
Markes International UNITY-Air Server-xr Installation Manual Download Page 37

 

 

 

 

QUI-1122 

Page 37 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

Chemstation software as the number is rounded to 1000.0 minutes.  Setting this value forces the 
split/splitless inlet to remain permanently in the splitless mode.   

The purge flow value is irrelevant.  Once the split/splitless inlet has been configured as described the 
column head pressure can be setup to give the desired flow rate/ velocity down the column. 

6.2

 

UNITY–Air Server-xr Electronic Gas Control with the Agilent 7890GC 

NOTE:

   To complete this installation the following 7890 parts are recommended.  They can be ordered 

directly from Agilent. 

Part no. 

Description 

Quantity 

G3430-60011 

Replacement hoodlum block assemblies 

1 

However, if these parts are not available at installation both the carrier gas and septum purge lines 
running between the EPC module and the Split/Splitless injector must be cut and extended using 1/8” 
unions and green PEEK tubing in order to facilitate connection to UNITY–Air Server-xr. 

6.2.1

 

Procedure 

 

Remove the top rear cover on the GC to provide access to the EPC module that is going to be used to 
regulate the carrier gas supply to UNITY–Air Server-xr. 

 

Remove the two hoodlum block assemblies, for the carrier supply and septum purge lines, from the 
split/splitless EPC module. 

 

 

Location of fixing screws for bulkhead connectors 

 

 

Fit the two replacement hoodlum block assemblies, and route the 1/16” tubing on both of these 
assemblies through the rear panel of the GC and towards the UNITY–Air Server-xr. 

NOTE

:  the carrier gas supply line has a 1/8” termination at the TD end while the septum purge line 

terminates in 1/16” tubing. 

 

If replacement hoodlum block assemblies are not available, the septum purge and carrier gas lines 
must be cut, extended, using 1/8” brass unions and 1/16” green PEEK tubing, and routed through 
the rear panel of the GC towards UNITY–Air Server-xr.  The lengths of PEEK tubing used should be no 
longer than required to reach the UNITY–Air Server-xr. 

 

EPC Module viewed 

from above 

EPC Module 
viewed from 

rear 

Septum Purge 

Connector 

Carrier Supply 

Connector 

Summary of Contents for UNITY-Air Server-xr
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands