manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Installation Manual

Share
Download
Markes International UNITY-Air Server-xr Installation Manual Download Page 36

 

 

 

 

QUI-1122 

Page 36 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

 

Location of EPC module with the 2 port EPC block fitted  

 

If a replacement EPC block assembly is not available, the septum purge and carrier gas lines must be 
cut, extended, using 1/8” brass unions and 1/16” green PEEK tubing, and routed through the rear 
panel of the GC towards UNITY–Air Server-xr.  The lengths of PEEK tubing used should be no longer 
than required to reach the UNITY–Air Server-xr. 

 

 

Carrier and septum purge lines extended with unions and PEEK tubing 

The stainless steel tubing for the carrier supply line is 1/16” while the septum purge line is 2 mm and will 
require a different ferrule when connected to the 1/8” brass union. 

NOTE

:   two 1/8” brass unions, 3 m of 1/16” green PEEK tubing and 1/8” graphitized vespel ferrules, 

including one for 2 mm tubing, are all contained within the Agilent GC Installation Kit. 

 

Connect the carrier gas supply line to the ‘Carrier Inlet’ port of UNITY–Air Server-xr and connect the 
septum purge line to the ‘Pressure Outlet’ port. 

6.1.2

 

6890 inlet settings 

Before the column pressure value is set, the MODE of operation of the inlet has to be configured.  

For correct control of UNITY–Air Server-xr the mode must be set only to SPLITLESS, and not split.  

In addition the splitless purge time value must be set to 999.99 minutes directly through the keyboard of 
the GC (6890 firmware revision A.03.08 or later required).  This value cannot be set using the 

1/8” Unions allowing 

extension of gas lines 

Replaced 2 port 

EPC block 

Routed tubing to 

UNITY-xr 

Standard 3 port 

EPC block 

Lines cut 

here 

Summary of Contents for UNITY-Air Server-xr
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands