manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Installation Manual

Share
Download
Markes International UNITY-Air Server-xr Installation Manual Download Page 21

 

 

 

 

QUI-1122 

Page 21 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

Loosen the screw at the bottom of the trap 
pneumatics assembly.  

Disconnect the 2 solenoid connections. Gently pull 
the trap pneumatic assembly towards the front of 
the instrument. 

Once clear of the screw, pull the pneumatics up 
and off the brass guiding block and rotate to the 
right. 

 

 

1.  Place the trap alignment tool into the cold trap 
box.   

2.  The tool should pass smoothly up to the o-ring 
in the heated valve before further gentle pressure 
moves the tool another 1-2 mm.   

If the tool does not move smoothly past the 
point where it leaves the cold trap box there 
may be a misalignment problem.   

3. Remove the trap alignment tool 

NEVER SWITCH UNITY-xr ON WITH THE 
TRAP ALIGNMENT TOOL INSTALLED 

 

1-2 mm past 

o-ring 

Summary of Contents for UNITY-Air Server-xr
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands