manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Installation Manual

Share
Download
Markes International UNITY-Air Server-xr Installation Manual Download Page 15

 

 

 

 

QUI-1122 

Page 15 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

 

5.

 

Place a second washer over the UNITY–Air Server-xr transfer line so that it can be secured against 
the inside wall of the GC oven. 

6.

 

Fit the clamp (

SERUTD-1125

) onto the transfer line, followed by the spacer (

SERUTD-1232

) 

secure with the M6 nut supplied with the transfer.  

 

 

Option 2 – Through Heated Injector Port 

NOTE:

   This option is only suitable if the inlet will not be required at any time. 

1.

 

Remove components from the injector (e.g. septum, liner etc.) to enable the transfer line to pass 
through unobstructed. 

2.

 

As the entry hole will generally be larger than the diameter of the metal line sleeve, one or more of 
the large washers supplied will be needed.  

 

Oven wall 

Oven wall 

Spacer 

Clamp 

Washer 

Washer 

Heated Transfer Line 

Nut 

Oven wall 

Oven wall 

Summary of Contents for UNITY-Air Server-xr
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands