manualshive.com logo in svg

Markem Imaje DigiConvert MC004-2014 P1082, Operating Instructions Manual, Page: 57 / 79

Share
Download
Markem Imaje DigiConvert MC004-2014 P1082 Operating Instructions Manual Download Page 57

 
DigiConvert Operating Instructions 
 
 

Copying this document, or disclosing it to third parties is not allowed without our approval. This document must not be used in any abusive way by the receiver or third 
parties. Fe Vogt GmbH 
DigiConvert Operating Instructions 

 

 

 

 

 

 

 

 

 

57 of 79 

Actuating the pulling cylinder 

 

Press the left-hand button to operate the pulling cylinder. 
The green background shows that the pulling cylinder is actuated. 
(The right-hand cylinder is only available in translative pull). 
 
 

 

Activating / deactivating the drive 

Press the button to deactivate the drive. 
 

Press the button again to reactivate the drive. 

 
 
Entering the sense of rotation 

 

Here you can enter the sense of rotation. 

 

 

Selecting the lead 

 

Here you can select the lead. After you have pressed the button you can enter a figure at the 
numerical keypad.  
 
 

Jogging in neg. direction / jogging in pos. direction 

 

Use these buttons to jog this axis individually at the JOG speed of the individual axis.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for DigiConvert MC004-2014 P1082
















































































Reviews:

No comments