manualshive.com logo in svg

Markem Imaje DigiConvert MC004-2014 P1082, Operating Instructions Manual, Page: 25 / 79

Share
Download
Markem Imaje DigiConvert MC004-2014 P1082 Operating Instructions Manual Download Page 25

 
DigiConvert Operating Instructions 
 
 

Copying this document, or disclosing it to third parties is not allowed without our approval. This document must not be used in any abusive way by the receiver or third 
parties. Fe Vogt GmbH 
DigiConvert Operating Instructions 

 

 

 

 

 

 

 

 

 

25 of 79 

Translative pull: 
 

 

Lead [%]: 

 

Motor 
torque [%]: 

 

Motor 
status: 

 

 

OFF 

 

Not initialised 

 

ON 

 

STO fault (e.g. emergency OFF active) 

 

Axis fault 

 

Motor 
selection: 
 

 

Deselected 

 

Selected 

 

Pneumatic 
system: 

, 

 

Open, closed 

 

Malfunction: 

 

Pneumatic cylinder has not reached 
desired position or drive not ready. 

 

 

 

 
 
 
Translative compensation: 
 

 

 

Homing status: 

 

Controller OFF 

 

Not homed 

(Blinking) 

Homing active 

 

Homed 

 

Limit switch: 

 

Limit switch was actuated 

 

Motor status: 

 

 

OFF 

 

Not initialised 

 

ON 

 

STO fault (e.g. emergency OFF active) 

 

Axis fault 

 

Motor selection: 
 

 

Deselected 

 

Selected 

 

Malfunction: 

 

Drive not ready 

 

 

 
 
 
Cutting table: 
 

 

Pneumatic 
system: 

, 

 

Open, closed 
(Touching changes state) 

 

 

 
 
 
 
 

Summary of Contents for DigiConvert MC004-2014 P1082
















































































Reviews:

No comments