manualshive.com logo in svg

Marco 1000201, Instruction Manual, Page: 2 / 28

Share
Download
Marco 1000201 Instruction Manual Download Page 2

2

Contents

Introduction..................................................................................................................................3

1. Chiller Specification.................................................................................................................4
                Installation Requirements.............................................................................................4
2. Safety......................................................................................................................................5
3. Basic Installation.....................................................................................................................8
 

Chiller Installation........................................................................................................8

 

CO2 Installation...........................................................................................................9

4. Operation...............................................................................................................................10
5. FRIIA Lite Installation Guide

..................................................................................................12

6. 

Sanitsation and Cleaning

.......................................................................................................23

7. Troubleshooting......................................................................................................................25

Box Contents

FRIIA Lite Chiller/

Carbonator

Part no.

Chiller 230Vac - 50/60Hz

1000202

2m length 3/8” Tube (water)

1800627

 3/4"BSPF x 3/8" Push fit 
Adaptor 

1400822

3/8” [Y] x 2-Way Divider

1400814

3/8” x 3/8” elbow

Fixing bracket

Power cable

User manual

n/a

 

It is highly recommended to fit a water regulator to the supply feed. In the event of 

mechanical failure a regulator set correctly will ensure the water supply is cut. Marco  

suggests 10 litres continuous flow.

FRIIA Lite Chiller

Part no.

Chiller 230Vac-50/60Hz

1000201

2m length 3/8” Tube 
(water)

1800627

3/4”BSPF x 3/8” Push fit 
Adaptor 

1400822

3/8” [Y] x 2-Way Divider

1400814

3/8” x 3/8” elbow
Fixing bracket
Power cable
User manual

n/a

Accessories

Part no.

Description

1600860#

FRIIA Fan Assembly (Wall Socket)

Summary of Contents for 1000201





























Reviews:

No comments