Marantz DVD Player, User Manual

Page: 23 / 57

23
ENGLISH
GETTING ST
ARTED USING
YOUR DVD PLA
YER/
ADJUSTING
AUDIO
AND VIDEO SETTINGS
(Example)
Audio1 Audio2 General Language Video
Dolby Digital Out
DTS Out -
96kHz PCM Out – 96kHz
3
48kHz
MPEG Out – MPEG
3
PCM
Move Exit
Dolby Digital 3 PCM
Dolby Digital
SETUP Select ENTER
Output Dolby Digital
(Example)
Audio1 Audio2 General Language Video
DTS Out -
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG
3
PCM
Move
Exit
Dolby Digital 3 PCM
Dolby Digital
SETUP
Dolby Digital Out
Change Dolby Digital output mode
Adjusting
Audio and
Video Settings
Audio1 Audio2 General Language Video
Dolby Digital Out – Dolby Digital
DTS Out – Off
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG
3
PCM
SETUP
Move Exit
Setup audio
Digital output format/tone adjust
continued
Using the Setup Screen
Menus
The procedure on this page describes how to operate the
menus on the Setup screen. These menus are used to set and
adjust a number of system settings. The various functions that
can be adjusted are covered throughout this manual. The
procedure on this page provides a basic outline for using the
Setup screen menus.
When setting up for the first time
It is recommended to set up player using the Setup Navigator
(
page 15 ). If you selected [Auto Start Off] when the Setup
Navigator appeared, you may still set up the player using the
Setup Navigator in the
General menu screen.
If you choose not to use the Setup Navigator, be sure to make
the necessary settings in the Setup screen
Audio 1 , Audio 2 , Video , and Language menus as
described on the following pages.
Some DVDs start playing automatically when loaded in the
player. If a DVD has been loaded, be sure to press
STOP
7
before proceeding.
Note
If the Setup screen is opened during playback of a DVD being
viewed in the letter box format, the screen may switch to the wide
screen format. This is not a malfunction, and the screen will return to
normal when the Setup screen is closed.
DIMMER
ENTER RETURN
T-C
+10
MENU
TOP
MENU
AUDIO SUBTITLE ANGLE
OSD PROGRAM
SETUP
LAST
MEMORY
CONDITION
MEMORY
CLEAR
0
9 8 7
6 5 4
3 2 1
REMOTE CONTROLLER
RC2100DV
3, 4, 5, 6
2
1
Press Power on the front panel.
2
Press SETUP .
The Setup screen appears.
3
Use the cursor buttons (
2 2 2 2 2
/
3 3 3 3 3
) to select the
menu you want.
As each menu is selected with the cursor, the settings
appear below the menu heading.
4
Use the cursor buttons (
∞
) to enter the menu.
The top item within the menu becomes highlighted.
5
Use the cursor buttons (
5 5 5 5 5
/
∞
) to select the
setting you want to change.
The options available for each setting appear to the right
when the setting is selected. The current setting appears
with the setting indicator lit.
6
Use the cursor buttons ( 3 3
3 3 3
) to enter the setting
options.
• Not all menu options can be changed while a disc is
playing. In these cases, the options appear grayed out
on the screen and cannot be adjusted. To change
these settings, press
STOP
7
first before pressing
SETUP .
• Operating the menu after pressing STOP
7
may
cancel the resume function.
• Some menu options are not immediately effective if set
while a disc is playing. To make these settings
effective, stop playback and then start again, or
change the settings while the disc is stopped.
SYS ANA MANU OPT SYNC RAND TRK PROG SCAN REPT ALL A-B DIG
REM TITL TIME TIME TRK CHP TOTL TOTL REM REM STEP TRK
DOWN MIX ANGLE LAST MEMO
Dolby V
96kHz 5.1CH CONDITION OSD
DUBBING
R
L
CD -R W CD -R W
1
(Example)