background image

DESCRIPTION

PART NUMBER

MARS, MARS ELITE & MARS SUPER SOFT RIDE KIT

85-9187

MARS, MARS ELITE & MARS SUPER FIRM RIDE KIT

85-9188

MARS, MARS ELITE & MARS SUPER X-FIRM RIDE KIT

85-9226

MARS, MARS ELITE & MARS SUPER BLACK OUTER ASSEMBLIE

85-9192

MARS, MARS ELITE & MARS SUPER YELLOW OUTER ASSEMBLIE

85-9195

MARS, MARS ELITE & MARS SUPER RED OUTER ASSEMBLIE

85-9203

MARS, MARS ELITE & MARS SUPER BLUE OUTER ASSEMBLIE

85-9204

MARS, MARS ELITE & MARS SUPER WHITE OUTER ASSEMBLIE

85-9205

MARS BLACK STICKER KIT

85-4128

MARS RED/WHITE STICKER KIT

85-4129

MARS ELITE STICKER KIT

85-4130

MARS SUPER RED STICKER  KIT

85-4132

MARS, MARS ELITE & MARS SUPER STEER TUBE/LEG ASSEMBLY

85-9213

MARS, MARS ELITE & MARS SUPER BUSHING SEAL KIT

85-4111

MARS REBOUND DAMPING ASSEMBLY

85-3016

MARS ELITE & MARS SUPER REBOUND DAMPING ASSEMBLY

85-9268

MARS COMPRESSION DAMPING ASSEMBLY

85-3018

MARS ELITE COMPRESSION DAMPING ASSEMBLY

85-3014

MARS SUPER COMPRESSION DAMPING ASSEMBLY

85-4062

MARS, MARS ELITE & MARS SUPER AIR CAP/PISTON ASSEMBLY

85-3033

MRD TUNING MANUAL

85-3696

MICROLUBE TUBE/GREASE GUN

85-3810

FORK PUMP

85-4069

ANTI-BOB KIT

85-4062

ANTI-BOB SEAL KIT

85-3686

28209 AVENUE STANFORD • VALENCIA, CA 91355

(661) 257-4411 • www.answerproducts.com

2001 MARS SERVICE MANUAL

P/N 85-3694

SPARE PARTS: 

Table 1

Spare parts can be ordered through your local dealer.  If you have any problems that you cannot

resolve with your dealer, you may call Answer Products Technical / Warranty Service Department 

at (661) 257-4411, 8:00 AM to 5:00 PM, Pacific Standard Time, Monday through Friday.  

Summary of Contents for 2001 MARS















Reviews: