background image

12 

Mouldboard extension

 

It  ensures  correct  arrangement  of  the  furrow 

especially  during  the  ploughing  of  stubble  and  areas 

covered by sod.

 

Coulter knife

 

blade

 

Alternative to the coulter discs when reduction of mass 

is  necessary.  It  is  also  recommended  for  large 

quantities  of  crop  residues,  organic  fertilizers  or 

stony  soils  when  a  coulter  disc  blade  would  be 

blocked

.

CAUTION! This plough is exclusively intended for agricultural work –  soil 

cultivation. Using the implement for tasks that differ from the intended use 

shall be regarded as misuse, resulting in loss of warranty.

 

CAUTION! The manufacturer shall not be liable for any damage arising out of 

misuse. Failure to follow the guidelines included in this instruction manual 

shall also be regarded as misuse.

 

 3 

 

General safety information 

The  plough  can  only  be  started,  used  and  repaired  by  persons  familiar  with  its 

operation and that of the tractor being used and the rules for its safe use and operation.

 

The manufacturer shall not be liable for any unauthorised alternation of the plough. Only 

genuine original MANDAM spare parts shall be used during the warranty period.

 

The plough must be operated with all precautionary measures, in particular:

 

each time before starting operation check the plough and the tractor whether their

condition guarantees safety during operation and travel,

minors, disabled or intoxicated persons (under the influence of alcohol or drugs)

must not operate the implement,

wear work clothes, shoes and gloves during maintenance,

do not exceed the maximum axle loads, tyre pressure and transport dimensions,

use only original cotter pins and pins,

do not approach the plough when it is being lifted or lowered,

do not stay between the plough and the tractor when the engine is running,

Summary of Contents for ORKAN 3+



































Reviews: