background image

                                         

1- Ignition Transformer

2- Photocell
3- Condenser

4- Burner Engine 
5- Fuel Pump

6- Solenoid
7- Brain

* The device is secured by pressure prosestat. Device will not enter the circuit unless sufficiant 

close- circuit pressure is provided.

B. GENERAL USAGE RULES

1- Switch off your device when you are filling the depot with diesel and wait for 1 hour without 
working.

2- Before restarting the unit, drain the sediment and water that accumulate on the bottom of the 
boiler by opening draining valve.

3- Clean the diesel filters at the outlet of the tank every 30 days. After the filter is cleaned, drain 
the air of the circuit.

4- Clean the electrodes and the turbulator of the burner every 6 days with a dry cloth.
5- Clean it with a photocell every 60 days.

6- At the beginning of each winter season, clean the soot  has accumulated in the boiler.
7- Clean the burner nozzle every 4 months.

Note: It is recommended that the maintenance procedures specified in items 4, 5, 6 and 7 are 

carried out by your authorized service.

                                                  

5

Summary of Contents for 20 MK














Reviews: