Maktec MT360 Instruction Manual Download Page 8

Dust extraction (Accessory) 

1

 

 

004939 

Use the vacuum head for dust extraction. To Install the 
vacuum  head,  raise  the  lock  lever  on  it.  Place  the 
vacuum  head  on  the  tool  base  so  that  its  top  will  be 
caught in the hook on the tool base. Insert the supports 
on the vacuum head into the hooks on the front of the tool 
base. 
Push down the lock lever onto the tool base. 

1
2

 

 

004940 

Then connect a vacuum cleaner to the vacuum head. 

   

004941 

To remove the vacuum head, raise the lock lever. Pull the 
vacuum  head  out  of  the  tool  base  while  holding  the 
supports between thumb and finger. 

MAINTENANCE 

 

CAUTION: 

• 

Always  be  sure  that  the  tool  is  switched  off  and 
unplugged before attempting to perform inspection 
or maintenance. 

• 

Never use gasoline, benzine, thinner, alcohol or the 
like.  Discoloration,  deformation  or  cracks  may 
result. 

 
 

Replacing carbon brushes 

1

 

 

001145 

Remove  and  check  the  carbon  brushes  regularly. 
Replace  when  they  wear  down  to  the  limit  mark.  Keep 
the carbon brushes clean and free to slip in the holders. 
Both  carbon  brushes  should  be  replaced  at  the  same 
time. Use only identical carbon brushes. 

For tool with the knob 

1

 

 

005111 

Release the lock lever and remove the knob by turning it 
counterclockwise. The compression spring will come out 
of  the  knob,  so  be  careful  not  to  lose  the  compression 
spring. 
Use a screwdriver to remove the brush holder caps. Take 
out  the  worn  carbon  brushes,  insert  the  new  ones  and 
secure the brush holder caps. 

1
2

 

 

004942 

To maintain product SAFETY and RELIABILITY, repairs, 
any  other  maintenance  or  adjustment  should  be 
performed by Makita Authorized Service Centers, always 
using Makita replacement parts. 

 
 
 

1. Brush holder cap
2. Screwdriver 

1. Knob 

1. Limit mark 

1. Support 
2. Lock lever 

1. Vacuum head 

Summary of Contents for MT360

















Reviews: