Maktec MT360 Instruction Manual Download Page 5

Stopper block 

1
2

3

4

5

 

 

004926 

As the rotary stopper has three adjusting hex bolts, you 
can  easily  obtain  three  different  depths  of  cut  without 
readjusting  the  stopper  pole.  To  adjust  the  hex  bolts, 
loosen the hex nuts on them and turn the hex bolts. After 
obtaining  the  desired  position,  tighten  the  hex  nuts  to 
secure the hex bolts. 

Switch action 

1

 

 

004927 

CAUTION: 

• 

Before  plugging  in  the  tool,  always  check  to  see 
that the tool is switched off. 

• 

Make sure that the shaft lock is released before the 
switch is turned on. 

To start the tool, move the switch lever to the I position. 
To stop the tool, move the switch lever to the O position. 

ASSEMBLY 

 

CAUTION: 

• 

Always  be  sure  that  the  tool  is  switched  off  and 
unplugged before carrying out any work on the tool. 

Installing or removing the bit 

1

2

3

 

 

004928 

 

CAUTION: 

• 

Install the bit securely. Always use only the wrench 
provided with the tool. A loose or overtightened bit 
can be dangerous. 

• 

Do not tighten the collet nut without inserting a bit or 
install small shank bits without using a collet sleeve. 
Either can lead to breakage of the collet cone. 

Insert the bit all the way into the collet cone. Press the 
shaft lock to keep the shaft stationary and use the wrench 
to tighten the collet nut securely. When using router bits 
with smaller shank diameter, first insert the appropriate 
collet sleeve  into  the  collet  cone,  then  install the  bit  as 
described above. 
To  remove  the  bit,  follow  the  installation  procedure  in 
reverse. 

OPERATION 

1

 

 

005112 

CAUTION: 

• 

Before  operation,  always  make  sure  that  the  tool 
body automatically rises to the upper limit and the 
bit does not protrude from the tool base when the 
lock lever is loosened. 

• 

Before  operation,  always  make  sure  that the chip 
deflector is installed properly. 

Set the tool base on the workpiece to be cut without the 
bit  making  any  contact.  Then  turn  the  tool  on  and  wait 
until the  bit  attains full speed.  Lower the tool  body  and 
move  the  tool  forward  over  the  workpiece  surface, 
keeping the tool base flush and advancing smoothly until 
the cutting is complete. 
When doing edge cutting, the workpiece surface should 
be on the left side of the bit in the feed direction. 

 

 

1. Chip deflector 

1. Shaft lock 
2. Wrench 
3. Bit 

1. Switch lever 

1. Stopper pole 
2. Chip deflector 
3. Stopper 
4. Adjusting hex 

bolt 

5. Hex nut 

Summary of Contents for MT360

















Reviews: