Maktec MT360 Instruction Manual Download Page 6

1

2

3

4

4

2

 

 

001984 

NOTE: 

• 

Moving the tool forward too fast may cause a poor 
quality of cut, or damage to the bit or motor. Moving 
the tool forward too slowly may burn and mar the 
cut. The proper feed rate will depend on the bit size, 
the  kind  of  workpiece  and  depth  of  cut.  Before 
beginning  the  cut  on  the  actual  workpiece,  it  is 
advisable to make a sample cut on a piece of scrap 
lumber. This will show exactly how the cut will look 
as well as enable you to check dimensions. 

1

2

3

4

 

 

001985 

NOTE: 

• 

When using the straight guide or the trimmer guide, 
be  sure  to  install  it  on  the  right  side  in  the  feed 
direction. This will help to keep it flush with the side 
of the workpiece. 

Straight guide 

1

 

 

004929 

The  straight  guide  is  effectively  used  for  straight  cuts 
when chamfering or grooving. 
Install  the  straight  guide  on  the  guide  holder  with  the 
thumb screw (B). Insert the guide holder into the holes in 

the tool base and tighten the thumb screw (A). To adjust 
the  distance  between  the  bit  and  the  straight  guide, 
loosen the thumb screw (B) and turn the fine adjusting 
screw (1.5 mm per turn). At the desired distance, tighten 
the thumb screw (B) to secure the straight guide in place. 

1
2

3

4

5

 

 

004930 

Wider straight guide of desired dimensions may be made 
by using the convenient holes in the guide to bolt on extra 
pieces of wood. 

1

2

55 mm

55 mm

3

 

 

004931 

When using a large diameter bit, attach pieces of wood to 
the straight guide which have a thickness of more than 
15 mm to prevent the bit from striking the straight guide. 
When cutting, move the tool with the straight guide flush 
with the side of the workpiece. 

Templet guide 

   

004932 

The templet guide provides a sleeve through which the 
bit passes, allowing use of the tool with templet patterns. 
To install the templet guide, loosen the screws on the tool 
base,  insert  the  templet  guide  and  then  tighten  the 
screws. 

1. More than 15 mm
2. Straight guide 
3. Wood 

1. Wing bolt (A) 
2. Guide holder 
3. Fine adjusting 

screw 

4. Wing bolt (B) 
5. Straight guide 

1. Straight guide 

1. Feed direction
2. Bit revolving 

direction 

3. Workpiece 
4. Straight guide 

1. Workpiece 
2. Bit revolving direction 
3. View from the top of the tool 
4. Feed direction 

Summary of Contents for MT360

















Reviews: