Maktec MT360 Instruction Manual Download Page 4

5. 

Check  the  bit  carefully  for  cracks  or  damage 
before  operation.  Replace  cracked  or 
damaged bit immediately. 

6. 

Avoid cutting nails. Inspect for and remove all 
nails from the workpiece before operation. 

7. 

Hold the tool firmly with both hands. 

8. 

Keep hands away from rotating parts. 

9. 

Make  sure  the  bit  is  not  contacting  the 
workpiece before the switch is turned on. 

10. 

Before using the tool on an actual workpiece, 
let  it  run  for  a  while.  Watch  for  vibration  or 
wobbling  that  could  indicate  improperly 
installed bit. 

11. 

Be careful of the bit rotating direction and the 
feed direction. 

12. 

Do not leave the tool running. Operate the tool 
only when hand-held. 

13. 

Always switch off and wait for the bit to come 
to  a  complete  stop  before  removing  the  tool 
from workpiece. 

14. 

Do  not  touch  the  bit  immediately  after 
operation;  it may  be  extremely  hot  and  could 
burn your skin. 

15. 

Do  not  smear  the  tool  base  carelessly  with 
thinner,  gasoline,  oil  or  the  like.  They  may 
cause cracks in the tool base. 

16. 

Use bits of the correct shank diameter suitable 
for the speed of the tool. 

17. 

Some material contains chemicals which may 
be  toxic.  Take  caution  to  prevent  dust 
inhalation  and  skin  contact.  Follow  material 
supplier safety data. 

18. 

Always  use  the  correct  dust  mask/respirator 
for  the  material  and  application  you  are 
working with. 

SAVE THESE INSTRUCTIONS. 

 

WARNING: 

DO  NOT  let  comfort  or  familiarity  with  product 
(gained from repeated use) replace strict adherence 
to  safety  rules  for  the  subject  product.  MISUSE  or 
failure  to  follow  the  safety  rules  stated  in  this 
instruction  manual  may  cause  serious  personal 
injury. 

 
 
 
 

FUNCTIONAL DESCRIPTION 

 

CAUTION: 

• 

Always  be  sure  that  the  tool  is  switched  off  and 
unplugged before adjusting or checking function on 
the tool. 

Adjusting the depth of cut 

1

2

3

4

5

6

 

 

004925 

Place the tool on a flat surface. Loosen the lock lever and 
lower  the  tool  body  until  the  bit  just  touches  the  flat 
surface. Press the lock lever down to lock the tool body. 
While  pressing  the  fast-feed  button,  move  the  stopper 
pole up or down until the desired depth of cut is obtained. 
Minute depth adjustments can be obtained by turning the 
stopper pole (1.5 mm per turn). 

 

CAUTION: 

• 

The depth of cut should not be more than 20 mm at 
a  pass  when  cutting  grooves.  For  extra-deep 
grooving operations, make two or three passes with 
progressively deeper bit settings. 

Nylon nut 

For tool without the knob 

The  upper  limit  of  the  tool  body  can  be  adjusted  by 
turning the nylon nut. Do not lower the nylon nut too low. 
The bit will protrude dangerously. 

For tool with the knob 

1

 

 

005111 

By turning the knob, the upper limit of the tool body can 
be adjusted. When the tip of the bit is retracted more than 
required  in  relation  to  the  base  plate  surface,  turn  the 
knob to lower the upper limit. Do not lower the knob too 
low. The bit will protrude dangerously. 

 

1. Knob 

1. Nylon nut 
2. Stopper pole 
3. Fast-feed button 
4. Adjusting hex 

bolt 

5. Stopper 
6. Lock lever 

Summary of Contents for MT360

















Reviews: