Maktec MT360 Instruction Manual Download Page 7

1

2

3

 

 

003692 

Secure the templet to the workpiece. Place the tool on 
the  templet  and  move  the  tool  with  the  templet  guide 
sliding along the side of the templet. 

1

2

3
4

5

6

7

 

 

003695 

NOTE: 

• 

The  workpiece  will  be  cut  a  slightly  different  size 
from  the  templet.  Allow  for  the  distance  (X) 
between the bit and the outside of the templet guide. 
The  distance  (X)  can  be  calculated  by  using  the 
following equation: 
Distance  (X)  =  (outside  diameter  of  the  templet 
guide - bit diameter) / 2 

Trimmer guide 

1

 

 

004935 

Trimming,  curved  cuts  in  veneers  for  furniture  and  the 
like can be done easily with the trimmer guide. The guide 
roller rides the curve and assures a fine cut. 
Install  the  trimmer  guide  on  the  guide  holder  with  the 
thumb screw (B). Insert the guide holder into the holes in 
the tool base and tighten the thumb screw (A). To adjust 
the  distance  between  the  bit  and  the  trimmer  guide, 
loosen the thumb screw (B) and turn the fine adjusting 
screw (1.5 mm per turn). When adjusting the guide roller 
up or down, loosen the thumb screw (C). After adjusting, 
tighten all the thumb screws securely. 

1
2
3

4

5

6

7

 

 

004936 

When cutting, move the tool with the guide roller riding 
the side of the workpiece. 

3

1

2

 

 

003701 

Dust cover (For tool with the knob) 

1

2

 

 

005113 

Dust cover prevents sawdust from being drawn into the 
tool in the inverted position. 
Install the dust cover as illustrated when using the tool 
with a router stand available in the market. 
Remove it when using the tool in the normal position. 

Spacer (For tool with the knob) 

1

2
3

 

 

005114 

The spacer prevents the router bit from dropping into the 
chuck when replacing the bit in the inverted position. 
Insert the spacer as illustrated when using the tool with a 
router stand available in the market. 

 

1. Collet nut 
2. Collet cone 
3. Spacer 

1. Pan head screw 
2. Dust cover 

1. Bit 
2. Guide roller 
3. Workpiece 

1. Wing bolt (A) 
2. Guide holder 
3. Fine adjusting 

screw 

4. Wing bolt (B) 
5. Wing bolt (C) 
6. Guide roller 
7. Trimmer guide 

1. Trimmer guide

1. Bit 
2. Base 
3. Templet 
4. Workpiece 
5. Distance (X) 
6. Outside 

diameter of the 
templet guide 

7. Templet guide

1. Templet guide
2. Screw 
3. Base plate 

Summary of Contents for MT360

















Reviews: