Makita XCU03, Instruction Manual

Page: 46 / 84

6 ENGLISH
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
LWPD\DFFLGHQWDOO\IDOORXWRIWKHWRROFDXVLQJLQMXU\WR
\RXRUVRPHRQHDURXQG\RX
CAUTION:
Do not install the battery cartridge
forcibly. ,IWKHFDUWULGJHGRHVQRWVOLGHLQHDVLO\LWLV
QRWEHLQJLQVHUWHGFRUUHFWO\
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
1
2
Ź 1. Indicator lamps 2. Check button
3UHVVWKHFKHFNEXWWRQRQWKHEDWWHU\FDUWULGJHWRLQGL -
FDWHWKHUHPDLQLQJEDWWHU\FDSDFLW\7KHLQGLFDWRUODPSV
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
EDWWHU\
7KHEDWWHU\
PD\KDYH
malfunctioned.
NOTE: Depending on the conditions of use and the
DPELHQWWHPSHUDWXUHWKHLQGLFDWLRQPD\GLIIHUVOLJKWO\
IURPWKHDFWXDOFDSDFLW\
Tool / battery protection system
7KHWRROLVHTXLSSHGZLWKDWRROEDWWHU\SURWHFWLRQV\V -
WHP7KLVV\VWHPDXWRPDWLFDOO\FXWVRIISRZHUWRWKH
PRWRUWRH[WHQGWRRODQGEDWWHU\OLIH7KHWRROZLOODXWR
-
PDWLFDOO\VWRSGXULQJRSHUDWLRQLIWKHWRRORUEDWWHU\LV
placed under one of the following conditions:
Status Indicator lamps
On Off Blinking
Overload
Overheat
Over
discharge
Overload protection
,IWKHWRROLVRYHUORDGHGE\HQWDQJOHGEUDQFKHVRURWKHU
debris, and the middle indicators start blinking and
WKHWRRODXWRPDWLFDOO\VWRSV
In this situation, turn the tool off and stop the application
that caused the tool to become overloaded. Then turn
the tool on to restart.
NOTICE:
Depending on the usage conditions,
the tool is automatically turned off without any
indication if the tool is overloaded by entangled
branches or debris. In this case, switch off the
tool and remove the battery cartridge, and then
remove entangled branches or debris using tools
such as pliers. After removing the branches or
debris, install the battery cartridge and turn on
the tool again.
Overheat protection for tool or
battery
7KHUHDUHWZRW\SHVRIRYHUKHDWLQJWRRORYHUKHDWLQJ
DQGEDWWHU\RYHUKHDWLQJ:KHQWKHWRRORYHUKHDWLQJ
RFFXUVDOOVSHHGLQGLFDWRUVEOLQN:KHQWKHEDWWHU\RYHU
heating occurs, indicator blinks.
,IWKHRYHUKHDWLQJRFFXUVWKHWRROVWRSVDXWRPDWLFDOO\
/HWWKHWRRODQGRUEDWWHU\FRROGRZQEHIRUHWXUQLQJWKH
tool on again.
Overdischarge protection
:KHQWKHEDWWHU\FDSDFLW\EHFRPHVORZWKHWRROVWRSV
DXWRPDWLFDOO\DQG
indicator blinks.
If the tool does not operate even when the switches are
RSHUDWHGUHPRYHWKHEDWWHU\IURPWKHWRRODQGFKDUJH
WKHEDWWHU\