background image

21 ENGLISH

NOTICE:

 

The bump feed will not operate prop-

erly if the nylon cutting head is not rotating.

NOTE:

 If the nylon cord does not feed out while 

tapping the head, rewind/replace the nylon cord 

by following the procedures in the section for the 

maintenance.

MAINTENANCE

WARNING:

 

Always be sure that the tool is 

switched off and battery cartridge is removed 

before attempting to perform inspection or main-

tenance on the tool.

 Failure to switch off and remove 

the battery cartridge may result in serious personal 

injury from accidental start-up.

NOTICE:

 

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

Cleaning the tool

Clean the tool by wiping off dust, dirt, or cut off grass 

with a dry cloth or one dipped in soapy water and wrung 

out. To avoid overheating of the tool, be sure to remove 

the cut off grass or debris adhered to the vent of the 

tool.

Replacing the nylon cord

WARNING:

 

Use only the nylon cord with 

diameter specified in this instruction manual. 

Never use heavier line, metal wire, rope or the 

like.

 Failure to do so may cause damage to the tool 

and result in serious personal injury.

WARNING:

 

Always remove the nylon cutting 

head from the tool when replacing the nylon cord. 

WARNING:

 

Make sure that the cover of the 

nylon cutting head is secured to the housing 

properly as described in this instruction manual.

 

Failure to properly secure the cover may cause the 

nylon cutting head to fly apart resulting in serious 

personal injury.

Replace the nylon cord if it is not fed any more. The 

method of replacing the nylon cord varies depending on 

the type of the nylon cutting head.

Summary of Contents for UR017G





























Reviews: