background image

16 ENGLISH

Correct combination of the cutting 

tool and the protector

CAUTION:

 

Always use the correct combi-

nation of cutting tool and the protector.

 A wrong 

combination may not protect you from the cutting tool, 

flying debris, and stones. It can also affect the bal

-

ance of the tool and result in an injury.

Cutting tool

Protector

Cutter blade

(2-tooth, 3-tooth, 4-tooth 

blades)

Nylon cutting head

Plastic blade

Installing the protector

WARNING:

 

Never use the tool without the 

guard or with the guard improperly installed.

 

Failure to do so can cause serious personal injury.

NOTE:

 The type of the protector supplied as the stan-

dard accessory varies depending on the countries.

For cutter blade

Attach the protector to the clamp using bolts.

1

2

Fig.19

►    

1.

 Clamp 

2.

 Protector

For nylon cutting head / plastic blade

CAUTION:

 

Take care not to injure yourself on 

the cutter for cutting the nylon cord.

Attach the protector to the clamp using bolts. After 

that, install the protector extension. Insert the protector 

extension to the protector and then snap the clips on. 

Make sure that the tabs on the protector extension fit 

into the slots on the protector.

1

2

4

3

6

5

Fig.20

►    

1.

 Protector 

2.

 Clip 

3.

 Protector extension 

4.

 Cutter 

5.

 Slot 

6.

 Tab

To remove the protector extension from the protec-

tor, unclasp the clips by inserting the hex wrench as 

illustrated.

1

2

Fig.21

►    

1.

 Hex wrench 

2.

 Clip

Installing the cutting tool

CAUTION:

 

Always use the supplied wrenches 

to remove or to install the cutting tool.

CAUTION:

 

Be sure to remove the hex wrench 

inserted into the tool head after installing the 

cutting tool.

NOTE:

 The type of the cutting tool(s) supplied as 

the standard accessory varies depending on the 

countries. The cutting tool is not included in some 

countries.

NOTE:

 Turn the tool upside down so that you can 

replace the cutting tool easily.

Summary of Contents for UR017G





























Reviews: