background image

16 ENGLISH

Trim large branches to the desired height using branch 

cutters before using this tool.

NOTICE:

 

Do not use the tool in a way that causes 

the motor to stop or to rotate extremely slowly.

NOTICE:

 

Do not attempt to cut thick branches.

NOTICE:

 

Do not allow the shear blades to con-

tact the ground during operation. The blades will 

be dulled, causing poor performance.

NOTICE:

 

Do not trim the wet grass or foliage of 

small trees.

Cutting long lawn

Do not try to cut long grass all at once. Instead, cut the 

lawn in steps. Leave a day or two between cuts until the 

lawn becomes evenly short.

NOTE:

 Cutting long grass to a short length all at once 

may cause the grass to die.

Trimming (for hedge trimmer)

CAUTION:

 

Be careful not to accidentally 

contact a metal fence or other hard objects while 

trimming.

 The blades may break and cause an injury.

CAUTION:

 

Be careful not to allow the shear 

blades to contact the ground.

 The tool may recoil 

and cause an injury.

 

CAUTION:

 

Overreaching with a hedge trim-

mer, particularly from a ladder, is extremely 

dangerous.

 Do not work while standing on anything 

wobbly or infirm.

NOTICE:

 

Do not attempt to cut branches thicker 

than 10 mm in diameter with the tool.

 Cut branches 

to the desired height using branch cutters before 

using the tool.

NOTICE:

 

Do not cut down dead trees or similar 

hard objects.

 Doing so may damage the tool.

NOTICE:

 

Do not trim the grass or weeds while 

using the shear blades.

 The blades may become 

tangled in the grass or weeds.

Hold the tool with one hand, pull the switch trigger while 

pressing the lock-off button, and then move it forward.

For basic operation, tilt the blades toward the trimming 

direction and move it calmly and slowly at the speed 

rate of 3 to 4 seconds per meter.

To tie a string at the desired height and to trim along it 

help you to cut a hedge top evenly.

Summary of Contents for UM600DWAE




















Reviews: