![background image](http://html.mh-extra.com/html/makita/tw161d/tw161d_instruction-manual_1722947007.webp)
7
ENGLISH
T o keep th e lamp of f , turn of f th e lamp status. F irst pull
and release th e sw itc h trigger. A nd th en press th e but-
ton
f or one sec ond w ith in 1 0 sec ond s.
T o turn on th e lamp status again, press th e button again
similarly.
NOTE:
To confirm the lamp status, pull the trigger.
When the lamp lights up by pulling the switch trigger,
th e lamp status is O N. W
h en th e lamp d oes not c ome
on, th e lamp status is O F F .
NOTE:
When the tool is overheated, the light flashes
for one minute, and then the LED display goes off. In
th is c ase, c ool d ow n th e tool bef ore operating again.
NOTE:
Use a dry cloth to wipe the dirt off the lens of
th e lamp. Be c aref ul not to sc ratc h th e lens of lamp, or
it may lower the illumination.
Reversing switch action
Fig.6:
1.
R ev ersing sw itc h lev er
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop.
C h anging th e
direction of rotation before the tool stops may dam
-
age th e tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
T h is tool h as a rev ersing sw itc h to c h ange th e d irec tion
of rotation. D epress th e rev ersing sw itc h lev er f rom th e
A sid e f or c loc kw ise rotation or f rom th e B sid e f or c oun-
terc loc kw ise rotation.
W
h en th e rev ersing sw itc h lev er is in th e neutral posi-
tion, th e sw itc h trigger c annot be pulled .
Changing the impact force
Fig.7:
1.
H ard
2.
S of t
3.
R ev erse rotation auto stop
mod e
4.
C h anged in th ree steps
5.
Button
Y ou c an c h ange th e impac t f orc e in th ree steps: h ard ,
sof t, and R ev erse rotation auto stop mod e.
T h is allow s a tigh tening suitable to th e w ork.
Every time the button is pressed, the number of blows
c h anges in th ree steps.
The function of Reverse rotation auto stop mode works only with pulling the trigger fully in counterclockwise tool
rotation. W
h en th e bolt/ nut gets enough loosened , th e tool stops th e impac t and rotation.
For approximately one minute after releasing the switch trigger, the impact force can be changed.
Impact force grade displayed
on panel
Maximum blows
Purpose
Example of application
H ard
3,6 00 min
-1
(/min)
T igh tening w h en f orc e and
speed are d esired .
A ssembling steel f rames.
S of t
2,000 min
-1
(/min)
Tightening when you need fine
adjustment with small diameter
bolt.
A ssembling f urniture.
R ev erse rotation auto stop
mod e
3,6 00 min
-1
(/min)
L oosening w ith auto stop
f unc tion.
D isassembling bolts/ nuts.
NOTE:
Reverse rotation auto stop mode is available only when the tool rotates counterclockwise. When rotating
c loc kw ise in R ev erse rotation auto stop mod e, th e impac t f orc e and speed are th e same as H ard impac t mod e.
NOTE:
When all lamps on the switch panel go out, the tool is turned off to save the battery power. The impact force
grade can be checked by pulling the switch trigger to the extent that the tool does not operate.
NOTE:
W
h ile pulling th e sw itc h trigger, th e impac t f orc e grad e c annot be c h anged .