12 ENGLISH
Driving staples
WARNING:
Do not use this stapler for fasten
-
ing electrical cables.
It is not designed for electric
cable installation and may damage the insulation of
electric cables thereby causing electric shock or fire
hazards.
WARNING:
Continue to place the contact
element firmly on the material until the staple is
driven completely.
Unintentional firing may cause
personal injuries.
WARNING:
Keep your face away from the tool
when operating the tool.
Failure to do so may cause
injury.
CAUTION:
Hold the tool firmly during
operation.
CAUTION:
Do not use the tool beyond the
continuous operating time allowed.
It otherwise
may cause damages to the tool resulting in personal
injury.
NOTICE:
The tool will not restart fastening
after five seconds no switch operation while the
contact element is placed on the workpiece. Pull
the contact element free from the workpiece and
reposition it in place to restart fastening.
You can operate the tool in either way of “single
sequential actuation” or “contact actuation”.
Single sequential actuation:
In this mode, you can drive one staple by one sequen
-
tial operation.
1.
Release the trigger lock.
2.
Place flat the contact element on the material.
3.
Hold the depth guide firmly against the material.
►
Fig.12:
1.
Trigger-lock button
2.
Contact element
3.
Depth guide
4.
Pull the switch trigger fully to drive a staple.
►
Fig.13:
1.
Switch trigger
5.
Release your finger from the switch trigger before
moving the contact element from the material.
You can also sequentially drive staples by pulling the
switch trigger while dragging the tool to the next area
with the contact element pressed against the material.
►
Fig.14
Contact actuation:
In this mode, you can drive staples consecutively.
1.
Release the trigger lock.
2.
Pull the switch trigger.
►
Fig.15:
1.
Trigger-lock button
2.
Switch trigger
3.
Place flat the contact element on the material to
drive a staple.
4.
Move the tool to the next areas with the switch
trigger pulled, and place flat the contact element on the
material to drive following staples.
►
Fig.16:
1.
Switch trigger
2.
Contact element
If the head of the staple remains above the workpiece
surface, drive the staple while holding the stapler head
firmly against the workpiece.
►
Fig.17
NOTE:
If the head of the staple still remains above
the workpiece even you hold the stapler head,
the material may not be suitable for the stapler.
Continuing use of the stapler on such material may
result in a damage to the stapler driver and/or stapler
jamming.
Anti dry fire mechanism
WARNING:
Always make sure that your
fingers are not placed on the switch trigger or
the contact element and the battery cartridge is
removed before loading the staples.
As all the staples loaded in the magazine become used
up, the tool will automatically stop firing to minimize
damage from dry firing and enhance safety.
Insert a new strip of staples in the magazine before
restarting operation.
Checking remaining staples
Learn remaining staples in the magazine through the
sight window. The pusher appears in the window and
moves towards the firing opening as the amount of
remaining staples becomes smaller.
►
Fig.18:
1.
Sight window
2.
Staples
3.
Pusher
Removing jammed staples
WARNING:
Always make sure that the trigger
is released, and the battery cartridge and staples
are removed before removing jammed staples.
CAUTION:
Do not remove the jammed staples
with bare hands.
The staples may jump out of the
magazine and cause an injury.
1.
Turn the locking lever in the direction shown in the
figure, then slide the sub magazine open.
2.
Remove all the staples left in the main magazine.
3.
Clear jammed staples from the firing opening.
►
Fig.19:
1.
Locking lever
2.
Sub magazine
3.
Main
magazine
4.
Firing opening
4.
Place the strip of staples back in the magazine,
and close the sub magazine securely.
Summary of Contents for ST001G
