10 ENGLISH
INSTALLATION
Positioning table saw
►
Fig.1:
1.
Hole diameter 8 mm
►
Fig.2:
1.
6 mm Std. washer
2.
No.10 wood screw 40
mm min. length
►
Fig.3:
1.
6 mm Std. washer
2.
6 mm Mounting bolt
& Nut tighten securely
Locate the table saw in a well lit and level area where you can
maintain good footing and balance. It should be installed in an
area that leaves enough room to easily handle the size of your
workpieces. The table saw should be secured with four screws or
bolts to the work bench or table saw stand using the holes pro-
vided in the bottom of the table saw. When securing the table saw
on the work bench, make sure that there is an opening in the top
of the work bench the same size as the opening in the bottom of
the table saw so the sawdust can drop through.
If during operation there is any tendency for the table
saw to tip over, slide or move, the work bench or table
saw stand should be secured to the floor.
Storing accessories
►
Fig.4:
1.
Push stick
►
Fig.5:
1.
Rip fence (Guide rule)
2.
Miter gauge
Push stick, Triangular rule, blade and wrenches can be
stored on the left side of the base and the rip fence and
miter gauge can be stored at the right side of the base.
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and unplugged
before adjusting or checking function on the tool.
Adjusting the depth of cut
►
Fig.6:
1.
Handle
The depth of cut may be adjusted by turning the handle.
Turn the handle clockwise to raise the blade or counter-
clockwise to lower it.
NOTE:
•
Use a shallow depth setting when cutting thin
materials in order to obtain a cleaner cut.
Adjusting the bevel angle
►
Fig.7:
1.
Arrow pointer
2.
Lock lever
Loosen the lock lever counterclockwise and turn the
handwheel until the desired angle (0° - 45°) is obtained.
The bevel angle is indicated by the arrow pointer.
After obtaining the desired angle, tighten the lock lever
clockwise to secure the adjustment.
CAUTION:
•
After adjusting the bevel angle, be sure to
tighten the lock lever securely.
Adjusting positive stops
►
Fig.8:
1.
90° adjusting screw
2.
45° adjusting screw
►
Fig.9
The tool is equipped with positive stops at 90° and 45°
to the table surface. To check and adjust the positive
stops, proceed as follows:
Move the handwheel as far as possible by turning it. Place
a triangular rule on the table and check to see if the blade is
at 90° or 45° to the table surface. If the blade is at an angle
shown in Fig. A, turn the adjusting screws clockwise; if it is at
an angle shown in Fig. B, turn the adjusting screws counter
-
clockwise to adjust the positive stops.
After adjusting the positive stops, set the blade at 90° to
the table surface. Then adjust the arrow pointer so that
its right edge is aligned to the 0° graduation.
►
Fig.10:
1.
Arrow pointer
Switch action
CAUTION:
•
Remove workpiece from the table.
•
Switch off the tool and then press in the restart button.
•
Before plugging in the tool, always be sure that
the tool is switched off.
For tool with button type switch
►
Fig.11:
1.
Switch
2.
Restart button
To start the tool, press the ON ( I ) button.
To stop it, press the OFF ( O ) button.
For tool with lever type switch
►
Fig.12:
1.
Switch
2.
Restart button
To start the tool, raise the switch lever. To stop it, lower
the switch lever.
Sub table (R)
►
Fig.13:
1.
Screws
►
Fig.14:
1.
Sub table (R)
This tool is provided with the sub table (R) on the right side of
the main table. To use the sub table (R), loosen two screws
on the right side counterclockwise, pull out the table (R) fully
and then tighten the two screws to secure it.
Sub table (back)
►
Fig.15:
1.
Screws
2.
Sub table (back)
To use the sub table (back), loosen the screws on the left and
right hand sides under the table and pull it out backwards to the
desired length. At the desired length, tighten the screw securely.
Slide table
►
Fig.16:
1.
Slide table
2.
Locking plate
CAUTION:
•
After using slide table, be sure to lock it by
moving the locking plate to the vertical position.
This tool is provided with the slide table on the left side. The slide
table slides back and forth. Pivot the locking plates on the back
and front sides to the horizontal position before using it.
