8
Note:
If the radio is in volume control status, press in the
tuning/volume control to become Tuning status.
4.
Keep on rotating the Tuning/Volume control knob until
the required frequency shown on the display.
5.
Rotate the Tuning/Volume control knob to get required
sound level.
6.
To turn off the radio, press the Power button. Display
will show OFF.
Storing stations in preset
memories
There are 5 memory presets for each waveband.
1.
Press the Power button to turn on the radio.
2.
Tune to required station using one of the methods
previously described.
3.
Press and hold down the required preset until radio
beeps. The preset number will appear in the display
and the station will be stored under chosen preset
button.
4.
Repeat this procedure for the remaining presets.
5.
Stations stored in preset memories can be overwritten
by following above procedures.
Recall stations from preset
memories
1.
Press the Power button to turn on the radio.
2.
Select the required waveband.
3.
Momentarily press the required Preset button, the
preset number and station frequency will appear in the
display.
Setting the radio alarm
When the radio alarm is selected, the radio will turn on
and play the chosen radio station at the chosen alarm
time. The radio alarm will continue for one hour unless
turned off by pressing the Power button. Pressing the
Power button whilst the alarm is activated will cancel the
alarm for 24 hours.
Note:
When the radio is in low battery status, the radio alarm
can’t be activated.
a. Setting radio alarm time:
1.
The radio alarm can be set either when radio is on or
off.
2.
Press and release radio alarm button
, the
radio alarm symbol will flash.
3.
During radio alarm symbol flashing, press
button
for more than 2 seconds followed by a beep.
4.
Display Hour will flash, rotate Tuning/Volume control
knob to select the hour then press
button again
to confirm hour setting.
5.
Follow same procedures of setting hour to set
required minute. Press
button to complete alarm
time setting.
b. Setting radio alarmed station
1.
During setting radio alarm time and radio alarm
symbol is flashing, press Band button to activate the
radio to select required wake-up band and station by
manual tuning and recall the preset stations. Press
button to complete radio alarm setting.
Display will show
.
2.
When above radio alarm time and station are set,
press and hold down radio alarm button
for
2 seconds followed by a beep to switch alarm on or
off. Display will show
when radio alarm is set.
Note:
If new radio alarm station is not selected, it will select
the last alarm station.
Setting the HWS (Humane Wake
System) buzzer alarm
A beep tone will activate when selecting the HWS buzzer
alarm.
The alarm beep will become shorter every 15 seconds for
one minute followed by one minute silence before
repeating the cycle.
The HWS alarm will sound for one hour until turning off by
pressing the Power button. Press the Power button whilst
the alarm is activated will cancel the alarm for 24 hours.
1.
The HWS buzzer alarm can be set either radio is on or
off.
2.
Press and release the HWS buzzer alarm button
, the symbol will flash.
3.
During the symbol flashes, long pressing the
button for more than 2 seconds followed by a beep
and display Hour digit will flash.
4.
Rotate Tuning/Volume control knob to select required
alarm hour, then press time set button
again.
The minute digit will then flash.
5.
Rotate Tuning/Volume control knob to select required
alarm minute, the press time set button
again to
complete HWS buzzer alarm setting.
6.
Press and hold down buzzer alarm button
for
more than 2 seconds followed by a beep to switch on
or off the HWS buzzer alarm.
Display will appear
when buzzer alarm has
been set.
Snooze function
1.
Whilst the alarm is activated, pressing any buttons
except the Power button will activate the snooze
function. The radio or HWS buzzer alarm will be
silenced with interval of 5 minutes.
2.
The display will flash both the snooze symbol
and
the alarm symbol. The snooze function can be
repeatedly during one hour that the alarms are active.
Sleep function
The sleep timer will automatically switched off the radio
after a preset time has elapsed.
1.
Press and continue to hold down the Power button for
more than 2 seconds, followed by a beep tone, the
