background image

R

epair

P 7 / 13  

6) Assembling linear ball bearing 3064

Cap

Felt ring 30

Linear ball 
bearing 3064

Turn base

Fig. 7

Fig. 7B

Fig. 7C

Fig. 7A

1. In this bearing, slide pipe is held with
    balls which is lined in 6 streaks.

Put linear ball bearing 3064 on
the hole of turn base.
When putting it, the balls
have to be located as illustrated
in Fig. 7A. 

2. Put 1R033 "bearing setting plate" on the
    linear ball bearing 3064, and slowly 
    press them with arbor press as 
    illustrated in Fig. 7B.

Approx.
3mm.

1R 033 Bearing 
             setting plate 

3. So, the linear ball bearing can be
    assembled to turn base with protrusion 
    of approx. 3mm as illustrated in Fig. 7C.  

7) Disassembling and assembling felt ring and cap

[ Disassembling ]
 1. Hitch the inside of cap and pull it out of turn base. 
     The disassembled cap can not be reassembled
     because of its deformation. It has to be replaced with
     new one, when assembling.

[ Assembling ]

1. Apply enough oil to felt ring 30 before assembling, for smooth sliding of slide pipe.
    And then, mount the felt ring 30 into cap as illustrated in Fig. 8.

Felt ring 30 (applied enough oil)

Cap

2. Assemble cap together with felt ring 30 to turn base by pressing them with arbor press
    as illustrated in Fig. 8. 

Fig. 8

Turn base

Summary of Contents for LS1011N














Reviews: