Makita LS0716FL, Instruction Manual

Page: 4 / 32

4
17.
Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18.
Use outdoor extension leads.
When tool is used outdoors, use only extension
cords intended for outdoor use.
19.
Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
20.
Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of moving
parts, free running of moving parts, breakage of
parts, mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorized service center unless otherwise
indicated in this instruction manual. Have defective
switches replaced by an authorized service facility.
Do not use the tool if the switch does not turn it on
and off.
21.
Warning.
The use of any accessory or attachment, other than
those recommended in this instruction manual or
the catalog, may present a risk of personal injury.
22.
Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.
ADDITIONAL SAFETY RULES FOR TOOL
ENB034-3
1.
Wear eye protection.
2.
Keep hands out of path of saw blade. Avoid con-
tact with any coasting blade. It can still cause severe
injury.
3.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly. Never
clamp or tie the blade guard into the open posi-
tion.
4.
Do not perform any operation freehand. The
workpiece must be secured firmly against the turn
base and guide fence with the vise during all opera-
tions. Never use your hand to secure the workpiece.
5.
Never reach around saw blade.
6.
Turn off tool and wait for saw blade to stop
before moving workpiece or changing settings.
7.
Unplug tool before changing blade or servicing.
8.
Always secure all moving portions before carry-
ing the tool.
9.
Stopper pin which locks the cutter head down is
for carrying and storage purposes only and not
for any cutting operations.
10.
Don’t use the tool in the presence of flammable liq-
uids or gases.
11.
Check the blade carefully for cracks or damage
before operation.
Replace cracked or damaged blade immediately.
12.
Use only flanges specified for this tool.
13.
Be careful not to damage the arbor, flanges (espe-
cially the installing surface) or bolt. Damage to
these parts could result in blade breakage.
14.
Make sure that the turn base is properly secured so
it will not move during operation.
15.
For your safety, remove the chips, small pieces, etc.
from the table top before operation.
16.
Avoid cutting nails. Inspect for and remove all nails
from the workpiece before operation.
17.
Make sure the shaft lock is released before the
switch is turned on.
18.
Be sure that the blade does not contact the turn
base in the lowest position.
19.
Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and stop-
ping.
20.
Make sure the blade is not contacting the workpiece
before the switch is turned on.
21.
Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling that
could indicate poor installation or a poorly balanced
blade.
22.
Wait until the blade attains full speed before cutting.
23.
Stop operation immediately if you notice anything
abnormal.
24.
Do not attempt to lock the trigger in the on position.
25.
Be alert at all times, especially during repetitive,
monotonous operations. Don’t be lulled into a false
sense of security. Blades are extremely unforgiving.
26.
Always use accessories recommended in this man-
ual. Use of improper accessories such as abrasive
wheels may cause an injury.
27.
Do not use the saw to cut other than aluminum,
wood or similar materials.