background image

 8

/ 2

3

[3] DISASSEMBLY/ASSEMBLY
[3] -2. Tool Holder Section (cont.)

R

epair

ASSEMBLY

1R214

Correction

Insert Impact bolt from
the HR5001C side of
1R214 and keep it aprox.
 60 sec
onds.

Impact bolt

Assembly of Rings to Impact Bolt

Assembly of Impact Bolt Section

Fig. 21

Fig. 22

Fig. 23

Before correction:
Rings' edges are protruding from
the top edge of the groove on
Impact bolt.

Groove on Impact bolt

Impact bolt Ring 19

Slide sleeve

Flat washer 36

O ring 71

Barrel complete

Do not forget to mount O Ring 71
to Barrel complete.

Flat washers 36 (2 pcs.)
have to be assembled
to the both side of 
Urethane washer 36.

Urethane washer 36

Rubber
ring 20

Shoulder
sleeve 19

Face the chamfered
edge to Impact bolt.

Face the conical side
to Slide sleeve.

Face the chamfered Side
to Shoulder sleeve 19.

Insert the assembled Impact
bolt section into Tool holder.

Fluoride ring 28

X ring 21

O ring 23

After correction:
Rings' edges are positioned
under the top edge of the
groove on Impact bolt.

Corrected

3) After installing Fluoride ring 28 on the groove of Impact bolt, the Ring is stretched and its edges are protruding from
    the groove.   Correct the deformation as illustrated in Fig. 21.

4) Assemble Impact bolt section, and insert it into Tool holder.   (Fig. 22)
5) Assemble Tool holder and Rings to Barrel complete.   (Fig. 23)
6) Take the reverse step of Disassembly to do the further steps.

Tool holder

Summary of Contents for HR4501C
























Reviews: