background image

P 1

4

/ 2

3

[3] DISASSEMBLY/ASSEMBLY
[3] -6. Crank section, Cylinder, Piston (cont.)

R

epair

DISASSEMBLY

4) Disassemble Piston in the order of 

Figs. 41 to 43

Set Connecting rod to the 
dead point on Cylinder
installation side by turning 
Crank shaft.

Disconnect Connecting rod
from Crank shaft.

Pull out Connecting rod from Crank shaft.

Remove O ring 27 
from Piston for 
replacement.

Crank shaft

Ring 38

Ring 38

Piston

Ring 38

O ring 27

Connecting rod

Crank shaft

Connecting rod

Connecting rod

Piston

Fig. 41

Fig. 42

Fig. 43

Screwdriver

Wooden piece to protect the edge of Crank housing
complete

Cylinder 34

Cylinder 34 can be removed by levering
up with a pair of screwdriver.

Screwdriver

Fig. 40A

3A) Cylinder 34 can be disassembled without 1R213. Refer to 

Fig. 40A

.

Ring 38 is left in Crank housing 
complete after removal of Cylinder 34.

Fig. 40

1R350

1R040

1R040

3) Disassemble Cylinder 34 as illustrated in 

Fig. 40

.

1R350

1R213

Turn Handle clockwise.  Cylinder 34 gripped with 
1R213's claw is pulled out from Crank housing complete.

Set Repairing jigs as follows.

Summary of Contents for HR4501C
























Reviews: