background image

P 1

1

/ 2

3

 

[3] DISASSEMBLY/ASSEMBLY
[3] -4. Active Dynamic Vibration Absorber (HR4510C and HR4511C only)

R

epair

ASSEMBLY

DISASSEMBLY

Spring guide

Spring guide

If Spring guide is
locked inside the
Absorber,

Push the locked
Spring guide to 
protrude from Absorber.

Now Spring guide
protrudes.

Spring guide

Mount Active dynamic vibration absorber
while keeping its position parallel to 
Crank housing.

Spring guide

Fig. 31

Fig. 32

Fig. 33

Fig. 34

1) Assemble Active dynamic vibration absorber.  (Fig. 30)
2) Set Spring guide in place as illustrated in Fig. 31.
3) Mount Active dynamic vibration absorber on the both side of Crank housing complete.   (Fig. 32)
4) Do the reverse step of disassembly in Fig. 27.  

[3] -5. Crank Cap Section

1) Remove Crank cap section as illustrated in Fig. 27.
2) Disassemble Crank cap section as illustrated in Figs. 33 and 34.

Link plate

Crank cap

Crank cap

Link plate and Change lever
can be disassembled from 
Crank cap.

M4x12 Pan head screw
(with threadlocker)

Crank lever

Torsion
spring 15

Pull off Torsion
spring 15 with
pliers. 

Remove Link lever. 

Link lever

Torsion spring 15

Link lever

Crank shaft

Crank lever

Link plate

While gripping Crank lever with water pump pliers, unscrew M4x12 
Pan head screw using cordlress impact driver with philips bit.

phillips bit

Summary of Contents for HR4501C
























Reviews: