![background image](http://html1.mh-extra.com/html/makita/dua301pt2/dua301pt2_instruction-manual_3980581019.webp)
19 ENGLISH
The saw chain may become loose after many hours
of use. From time to time check the saw chain tension
before use.
1.
Loosen the retaining nut a bit to loosen the
sprocket cover lightly.
►
Fig.19:
1.
Retaining nut
2.
Lift up the guide bar tip slightly and adjust the
chain tension. Turn the chain adjusting screw counter
-
clockwise to tighten, turn it clockwise to loosen.
Tighten the saw chain until the lower side of the saw
chain fits in the guide bar rail as illustrated.
►
Fig.20:
1.
Guide bar
2.
Saw chain
3.
Chain adjust
-
ing screw
3.
Keep holding the guide bar lightly and attach the
sprocket cover.
Make sure that the saw chain does not loose at the
lower side.
4.
Tighten the retaining nut to secure the sprocket
cover.
►
Fig.21:
1.
Retaining nut
Installing or removing the angled
attachment
Optional accessory
CAUTION:
Before installing or removing the
angled attachment, be sure to attach the guide
bar cover to the tool.
You can change the angle of the tool head by attaching
the angled attachment to the tool.
1.
Loosen the lock ring by turning the lock ring coun-
terclockwise, then extend the pipe approximately 10 cm
or more, and then tighten the lock ring by turning the
lock ring clockwise.
►
Fig.22:
1.
10 cm or more
2.
Lock ring
3.
Pipe
2.
Loosen 2 bolts with the hex wrench, and then
remove the pipe from the head of the tool.
►
Fig.23:
1.
Bolt
3.
Remove the caps from the angled attachment.
►
Fig.24:
1.
Cap
4.
Align the hole on the pipe with that on the attach-
ment, and then insert the pipe into the attachment.
►
Fig.25:
1.
Hole
2.
Bolt
3.
Pipe
5.
Tighten 2 bolts to fix the attachment.
►
Fig.26:
1.
Bolt
6.
Attach the head of the tool to the attachment.
To fix the head of the tool vertically, fix the attachment
by tightening the bolt to the hole on the attachment
shown in the figure, and then tighten the other bolt.
►
Fig.27:
1.
Bolt
2.
Hole
To fix the head of the tool horizontally, fix the attachment
by tightening the bolt to the hole on the attachment
shown in the figure, and then tighten the other bolt.
►
Fig.28:
1.
Bolt
2.
Hole
To remove the angled attachment, perform the installa-
tion procedure in reverse.
OPERATION
Lubrication
NOTICE:
When filling the chain oil for the first
time, or refilling the tank after it has been com
-
pletely emptied, add oil up to the bottom edge of
the filler neck. The oil delivery may otherwise be
impaired.
NOTICE:
Use the saw chain oil exclusively for
Makita chain saws or equivalent oil available in
the market.
NOTICE:
Never use oil including dust and parti-
cles or volatile oil.
NOTICE:
When pruning trees, use botanical oil.
Mineral oil may harm trees.
NOTICE:
Before the cutting operation, make sure
that the oil tank cap is tightened securely.
Saw chain is automatically lubricated when the tool is in
operation. Check the amount of remaining oil in the oil
tank periodically.
►
Fig.29:
1.
Oil tank
To refill the tank, place the tool on a flat surface, then
push the button on the oil tank cap so that the button on
the other side stands up, and then remove the oil tank
cap by turning it.
The proper amount of oil is 160 ml. After refilling the
tank, make sure that the oil tank cap is tightened
securely.
►
Fig.30:
1.
Oil tank cap
2.
Tighten
3.
Loosen
NOTE:
If it is difficult to remove the oil tank cap,
insert the box wrench into the slot of the oil tank
cap, and then remove the oil tank cap by turning it
counterclockwise.
►
Fig.31:
1.
Slot
2.
Box wrench
After refilling, hold the tool away from the tree. Start it
and wait until lubrication on saw chain is adequate.
►
Fig.32
Summary of Contents for DUA301PT2
