background image

14

 Refuelling

FOLLOW THE SAFETY PRECAUTIONS!

Be careful and cautious when handling fuels.

The engine must be switched off!

Thoroughly clean the area around the caps, to prevent dirt from 
getting into the fuel or oil tank.

Unscrew the cap and 

Þ

 ll the tank with fuel (fuel/oil mixture) 

or chain oil as the case may be. Fill up to the bottom edge 
of the 

Þ

 ller neck. Be careful not to spill fuel or chain oil!

Tightly screw on the cap.

Clean screw cap and tank after refuelling.

Lubricating the chain

During operation there must always be suf

Þ

 cient chain oil in 

the chain-oil tank to provide good chain lubrication. One 

Þ

 lling 

is suf

Þ

 cient for about one half-hour of continuous operation. 

While working make sure there is enough chain oil in the tank. 
If necessary, add oil. 

The engine must be switched off!

 

NEVER USE WASTE OIL

Waste oil is very dangerous for the environment.

Waste oil contains high amounts of carcinogenic substances.

Residues in waste oil result in a high degree of wear and tear 
at the oil pump and the sawing device.

In case of damage caused by using waste oil or unappropriate 
chain oil the product guarantee will be null and void.

Your salesman will inform you about the use of chain oil.

AVOID SKIN AND EYE CONTACT

Mineral oil products degrease your skin. If your skin comes in 
contact with these substances repeatedly and for an extended 
period of time, it will desiccate. Various skin deseases may result. 
In addition, allergic reactions are known to occur.

Eyes can be irritated by contact with oil. If oil comes into your 
eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

age to the oil pump or other parts.

The next time you use the saw, 

Þ

 ll the tank with BIOTOP 

chain oil again.

 

In case of damage caused by using waste 

oil or unappropriate chain oil the product guarantee will be 
null and void.

Your salesman will inform you about the use of chain oil.

A

B

chain oil

fuel/oil mixture

Important note on bio-degradable chain oils

If you are not planning to use the saw again for an ex-
tended period of time, empty the oil tank and put in a small 
amount of regular 

engine oil

 (SAE 30), and then run the 

saw for a time. This is necessary to 

ß

 ush out all remain-

ing bio-degradable oil from the oil tank, oil-feed system, 
chain and guide bar, as many such oils tend to leave sticky 
residues over time, which can cause dam-

waste oil

Summary of Contents for DCS 6400

































Reviews: