background image

21

1

2

Files and how to work with them

Sharpen using a special 

Þ

 le holder with a saw chain round 

Þ

 le.

 

Normal round 

Þ

 les are not appropriate for this work. See „Ac-

cessories“ for the order number.

File the 

Þ

 rst cutter half with a  5.5 mm  dia. round saw-chain 

Þ

 le, then switch to a 4.8 mm dia. 

Þ

 le.

The 

Þ

 le should cut only when pushed forwards (arrow). Lift the 

Þ

 le when leading it backwards.

First sharpen the shortest cutter. The length of this cutter is then 
the standerd for all other cutters of the chain.

New saw teeth must be 

Þ

 led to the exact same shape as the 

used teeth, including on their running surfaces.

Always guide the 

Þ

 le horizontally (10

°

 to the guide bar).

E

The 

Þ

 le holder makes 

Þ

 le guidance easier. It is marked for the 

correct sharpening angle of 25° (keep the marks parallel with 
the chain when 

Þ

 ling, see illustration) and limits the cut depth 

to the correct 4/5 of the 

Þ

 le diameter. See „Accessories“ for the 

order number.

4/5

25°

F

After having sharpened the chain, the height of the depth limiter 
must be checked by means of a chain gauge. See „Accessories“ 
for the order number.

Correct even the smallest excess height with a special 

ß

 at 

Þ

 le (

1

). See „Accessories“ for the order number.

Round off the front of the depth limiter (

2

).

D

Summary of Contents for DCS 6400

































Reviews: