background image

[4] ADJUSTMENT
[4]-1. Side blades, Center blade 

Fig. 13

Fig. 12

Gaps between Center blade and Side blades are defined depending on the thickness of the work piece.  
Chose up two Thickness gauges from 1R366 for adjustment of the gaps referring to the following table.

(1) Loosen M6x10 Hex socket set screw, as illustrated in Fig. 12.

(2) Adjust the gaps by inserting 1R366 into the gap A and B, and turning M4x25 Hex socket head bolt as illustrated
      in Fig. 13

(3) After adjusting the gaps, tighten M6x10 Hex socket set screw with Hex wrench 3.  Refer to Fig. 12.

Side blade L

Side 
blade L

Inserting the selected Thickness gauges into the gap A, 
turn M4x25 Hex socket head bolt with Hex wrench 3
until the gap A can be adjusted to the required size. 
In the same way, adjust the gap B. (almost same size to 
Gap A)

Center blade

Center blade

Side blade R

Side 
blade R

Thickness of
Work piece (mm)

less than 0.8

more than 1.3

0.1 + 0.2

0.1

0.04 + 0.06

0.8 - less than 1.3

0.2
0.3

0.05 + 0.15

Required gap between

A and B  (mm)

Combination of 
Thickness gauge

A

B

M6x10 Hex socket 
set screw
(on Side blade R side)

Hex wrench 3

Loosen M6x10 Hex socket set screw
by turning with Hex wrench 3 approx.
360 degrees.
But, do not remove this screw.

1R366
Thickness gauge

M4x25 Hex socket
head bolt  
(on Side blade L side)

P 7/ 9

R

epair

Summary of Contents for BJS160










Reviews: