8 ENGLISH
6.
Use the specified surface of the wheel to per
-
form the grinding.
7.
Do not leave the tool running. Operate the tool
only when hand-held.
8.
Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
9.
Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
10.
Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
11.
Use only flanges specified for this tool.
12.
For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
13.
Check that the workpiece is properly
supported.
14.
Pay attention that the wheel continues to
rotate after the tool is switched off.
15.
If working place is extremely hot and humid,
or badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure opera-
tor safety.
16.
Do not use the tool on any materials contain-
ing asbestos.
17.
When use cut-off wheel, always work with
the dust collecting wheel guard required by
domestic regulation.
18.
Cutting discs must not be subjected to any
lateral pressure.
19.
Do not use cloth work gloves during operation.
Fibers from cloth gloves may enter the tool, which
causes tool breakage.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and unplugged before adjusting or
checking function on the tool.
Shaft lock
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
►
Fig.1:
1.
Shaft lock
NOTICE:
Never actuate the shaft lock when the
spindle is moving.
The tool may be damaged.
Switch action
CAUTION:
Before plugging in the tool, always
check to see that the slide switch actuates prop-
erly and returns to the "OFF" position when the
rear of the slide switch is depressed.
CAUTION:
Switch can be locked in "ON" posi-
tion for ease of operator comfort during extended
use. Apply caution when locking tool in "ON"
position and maintain firm grasp on tool.
To start the tool, slide the slide switch toward the “I
(ON)” position by pushing the rear of the slide switch.
For continuous operation, press the front of the slide
switch to lock it.
To stop the tool, press the rear of the slide switch, then
slide it toward the “O (OFF)” position.
►
Fig.2:
1.
Slide switch
Unintentional restart proof
The tool does not start with the switch being lock-on
even when the tool is plugged.
To cancel the unintentional restart proof, return the
power switch to OFF position.
NOTE:
Wait more than one second before restarting
the tool when unintentional restart proof functions.
NOTE:
When the tool is overloaded and the tool
temperature reaches a certain level, the tool may
automatically stop. In this situation, let the cool before
turning on the tool again.
Soft start feature
Soft start feature reduces starting reaction.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Summary of Contents for 9558HNR
