10 ENGLISH
3.
Loosen the clamping screw (B) and adjust the
distance between the trimmer bit and the trimmer guide
by turning the adjusting screw (1 mm per turn). At the
desired distance, tighten the clamping screw (B) to
secure the trimmer guide in place.
►
Fig.16:
1.
Adjusting screw
2.
Guide holder
3.
Trimmer guide
4.
Chip deflector
4.
When cutting, move the tool with the guide roller
riding the side of the workpiece.
►
Fig.17:
1.
Workpiece
2.
Trimmer bit
3.
Guide roller
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Replacing carbon brushes
►
Fig.18:
1.
Limit mark
Check the carbon brushes regularly.
Replace them when they wear down to the limit mark.
Keep the carbon brushes clean and free to slip in the
holders. Both carbon brushes should be replaced at the
same time. Use only identical carbon brushes.
1.
Use a screwdriver to remove the brush holder
caps.
2.
Take out the worn carbon brushes, insert the new
ones and secure the brush holder caps.
►
Fig.19:
1.
Brush holder cap
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard
-
ing these accessories, ask your local Makita Service
Center.
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Trimmer bits
Straight bit
►
Fig.20
D
A
L1
L2
6
20
50
15
1/4″
6
8
50
18
1/4″
6
6
50
18
1/4″
Unit:mm
U-grooving bit
►
Fig.21
D
A
L1
L2
R
6
6
60
28
3
1/4″
Unit:mm
V-grooving bit
►
Fig.22
D
A
L1
L2
θ
1/4″
20
50
15
90°
Unit:mm
Drill point flush trimming bit
►
Fig.23
D
A
L1
L2
L3
6
6
60
18
28
1/4″
Unit:mm
Drill point double flush trimming bit
►
Fig.24
D
A
L1
L2
L3
L4
6
6
70
40
12
14
1/4″
Unit:mm
Corner rounding bit
►
Fig.25
D
A1
A2
L1
L2
L3
R
6
25
9
48
13
5
8
1/4″
6
20
8
45
10
4
4
1/4″
Unit:mm
Summary of Contents for 3711
