Makita 3711 Page 8 Instruction Manual Download

Page: 8 / 66

8 ENGLISH

Save all warnings and instruc

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Trimmer safety warnings

Hold the power tool by insulated gripping

surfaces only, because the cutter may contact

its own cord.

Cutting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by your hand or against the body

leaves it unstable and may lead to loss of control.

The trimmer bit shank must match the

designed collet chuck.

Only use a trimmer bit that is rated at least equal

to the maximum speed marked on the tool.

Wear hearing protection during extended

period of operation.

Handle the trimmer bits very carefully.

Check the trimmer bit carefully for cracks or

damage before operation. Replace cracked or

damaged bit immediately.

Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

Hold the tool firmly.

10.

Keep hands away from rotating parts.

11.

Make sure the trimmer bit is not contacting the

workpiece before the switch is turned on.

12.

Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate improperly installed bit.

13.

Be careful of the trimmer bit rotating direction

and the feed direction.

14.

Do not leave the tool running. Operate the tool

only when hand-held.

15.

Always switch off and wait for the trimmer bit

to come to a complete stop before removing

the tool from workpiece.

16.

Do not touch the trimmer bit immediately after opera

tion; it may be extremely hot and could burn your skin.

17.

Do not smear the base carelessly with thinner, gaso

line, oil or the like. They may cause cracks in the base.

18.

Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

19.

Always use the correct dust mask/respirator for

the material and application you are working with.

20.

Place the tool on stable area.

Otherwise falling

accident may occur and cause an injury.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION:

Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Adjusting trimmer bit protrusion

To adjust the bit protrusion, loosen the clamping screw

and move the base up or down as desired by turning

the adjusting screw. After adjusting, tighten the clamp

ing screw firmly to secure the base.

►

Fig.1:

Base

Scale

Bit protrusion

Clamping

screw

Adjusting screw

Switch action

CAUTION:

Before plugging in the tool, always

be sure that the tool is switched off.

To start the tool, move the switch lever to the I position.

To stop the tool, move the switch lever to the O position.

►

Fig.2:

Switch lever

Electronic function

The tool is equipped with the electronic functions for

easy operation.

Indication lamp

►

Fig.3:

Indication lamp

The indication lamp lights up green when the tool is

plugged. If the indication lamp does not light up, the

mains cord or the controller may be defective. The indi

cation lamp is lit but the tool does not start even if the

tool is switched on, the carbon brushes may be worn

out, or the controller, the motor or the ON/OFF switch

may be defective.

Unintentional restart proof

The tool does not start with the switch lever in I position

even when the tool is plugged.

At this time, the indication lamp blinks in red and shows

the unintentional restart proof device is on function.

To cancel the unintentional restart proof, return the

switch lever to O position.

Soft start feature

Soft-start feature minimizes start-up shock, and makes

the tool start smoothly.

Summary of Contents for 3711



































































Search results

Summary of Contents for 3711

Reviews:

Related manuals for 3711

Brands by name

Popular brands

Makita 3711, Instruction Manual

Search results

Summary of Contents for 3711

Reviews:

Related manuals for 3711

Brands by name

Popular brands