![background image](http://html.mh-extra.com/html/makita/3612/3612_instruction-manual_228841006.webp)
6
ENGLISH
Explanation of general view
1-1. Stopper pole
1-2. Fast-feed button
1-3. Adjusting hex bolt
1-4. Stopper block
2-1. Knob
3-1. Nylon nut
3-2. Stopper pole
3-3. Fast-feed button
3-4. Adjusting hex bolt
3-5. Stopper block
3-6. Lock lever
4-1. Stopper pole
4-2. Hex bolt
4-3. Hex nut
4-4. Stopper block
5-1. Switch lever
6-1. Lock-off button
6-2. Switch trigger
7-1. Speed adjusting dial
8-1. Wrench
8-2. Shaft lock
8-3. Lock lever
9-1. Chip deflector
10-1. Workpiece
10-2. Bit revolving direction
10-3. View from the top of the tool
10-4. Feed direction
11-1. Feed direction
11-2. Bit revolving direction
11-3. Workpiece
11-4. Straight guide
13-1. Wing bolt (A)
13-2. Guide holder
13-3. Fine adjusting screw
13-4. Wing bolt (B)
13-5. Straight guide
14-1. More than 15mm (5/8")
14-2. Straight guide
14-3. Wood
16-1. Templet guide
16-2. Screw
16-3. Base plate
17-1. Templet guide
17-2. Lock plate lever
18-1. Bit
18-2. Base
18-3. Templet
18-4. Workpiece
18-5. Distance (X)
18-6. Outside diameter of the templet
guide
18-7. Templet guide
20-1. Wing bolt (A)
20-2. Guide holder
20-3. Fine adjusting screw
20-4. Wing bolt (B)
20-5. Wing bolt (C)
20-6. Trimmer guide
20-7. Guide roller
21-1. Bit
21-2. Guide roller
21-3. Workpiece
22-1. Pan head screw
22-2. Dust cover
23-1. Collet nut
23-2. Collet cone
23-3. Spacer
24-1. Vacuum head
25-1. Vacuum head
25-2. Screws
26-1. Vacuum head
27-1. Support
27-2. Lock lever
29-1. Limit mark
30-1. Brush holder cap
30-2. Knob
30-3. Screwdriver
SPECIFICATIONS
Model 3612
3612C
Collet chuck capacity
12 mm or 1/2"
Plunge capacity
0 - 60 mm
No load speed (min
-1
)
22,000
9,000 - 23,000
Overall length
297 mm (324 mm with knob)
Base diameter
160 mm
Net weight
5.8 kg
6.0 kg
Safety class
/II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
ENE010-1
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.32 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
Summary of Contents for 3612
