![background image](http://html.mh-extra.com/html/makita/3612/3612_instruction-manual_228841010.webp)
10
Fig.17
Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.
Fig.18
NOTE:
•
The workpiece will be cut a slightly different size
from the templet. Allow for the distance (X)
between the bit and the outside of the templet
guide. The distance (X) can be calculated by using
the following equation:
Distance (X) = (outside diameter of the templet
guide - bit diameter) / 2
Trimmer guide (optional accessory)
Fig.19
Trimming, curved cuts in veneers for furniture and the
like can be done easily with the trimmer guide. The
guide roller rides the curve and assures a fine cut.
Install the trimmer guide on the guide holder with the
wing bolt (B). Insert the guide holder into the holes in the
tool base and tighten the wing bolt (A). To adjust the
distance between the bit and the trimmer guide, loosen
the wing bolt (B) and turn the fine adjusting screw (1.5
mm per turn). When adjusting the guide roller up or
down, loosen the wing bolt (C). After adjusting, tighten
all the wing bolts securely.
Fig.20
When cutting, move the tool with the guide roller riding
the side of the workpiece.
Fig.21
Dust cover (Accessory)
Fig.22
To suit the tool when using in the inverted position with
Makita Router Stand.
This accessory prevents sawdust from being drawn
through the tool in the inverted position.
It is not recommended for use in the normal position.
However, we do recommend its use in the inverted
mode.
Fit as shown in the figure.
Spacer (Accessory)
Fig.23
When operating the tool in the inverted position with the
Makita Router Stand, use the spacer.
The spacer prevents the router bit from dropping in to
the chuck when replacing the bit.
Install the spacer as shown in the figure.
Vacuum head set (Accessory)
For tool without lock plate
Fig.24
Use the vacuum head for dust extraction. Install the
vacuum head on the tool base using the two screws.
Fig.25
For tool with lock plate
Fig.26
Use the vacuum head for dust extraction. To Install the
vacuum head, raise the lock lever on it. Place the
vacuum head on the tool base so that its top will be
caught in the hook on the tool base. Insert the supports
on the vacuum head into the hooks on the front of the
tool base.
Push down the lock lever onto the tool base.
Fig.27
Then connect a vacuum cleaner to the vacuum head.
Fig.28
To remove the vacuum head, raise the lock lever. Pull
the vacuum head out of the tool base while holding the
supports between thumb and finger.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
Replacing carbon brushes
Fig.29
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
Fig.30
NOTE:
•
When replacing carbon brush located on the same
side as the knob, remove the knob first before
unscrewing the brush holder cap.
CAUTION:
•
Be sure to re-install the knob after inserting new
carbon brush.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
ACCESSORIES
CAUTION:
•
These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
Summary of Contents for 3612
