background image

2

Limited WARRANTY:

Make Noise warrants this product to be free of defects in materials or construction for a period of one year 

from the date of purchase (proof of purchase/invoice required). 

Malfunction resulting from wrong power supply voltages, backwards or reversed eurorack bus board cable 

connection, abuse of the product or any other causes determined by Make Noise to be the fault of the user 

are not covered by this warranty, and normal service rates will apply. 

During the warranty period, any defective products will be repaired or replaced, at the option of Make Noise, 

on a return-to-Make Noise basis with the customer paying the transit cost to Make Noise. Please contact 

[email protected]

  for Return To Manufacturer Authorization. 

Make Noise implies and accepts no responsibility for harm to person or apparatus caused through operation 

of this product.

Please contact 

[email protected]

 with any questions, needs & comments, otherwise... 

go MAKE NOISE!

http://www.makenoisemusic.com 

THANK YOU

Beta Analyst: Peter Speer 

Test Subjects: James Cigler 

Spiritual Advisor: Richard Devine

Special Thanx to MATHS!

About This Manual:

Written by Tony Rolando

Edited by Walker Farrell

Illustrated by W.Lee Coleman

Summary of Contents for FUNCTION










Reviews: