background image

www.major-equipment.com

4

NEVER PLACE LIMBS UNDER THE MACHINE WHILE ROTOR(S) ARE TURNING. ROTORS CAN REMAIN 

TURNING FOR UP TO 1 MINUTE AFTER TURNING OFF THE HYDRAULIC MOTOR .

Workstation

The operator must remain seated while working the machine. If the machine is a winged unit and the wings need to be 

raised/lowered the operator must not leave the tractor. Never leave the workstation (tractor cab, digger cab) with the 

hydraulic motor running and blades rotating. Always apply the handbrake and turn off the hydraulic motor before leaving 

the cab.

NEVER OPERATE THE HYDRAULICS WITH THE TRACTOR SWITCHED OFF

Regulations for use of the transmission

The transmission between the gearboxes is protected by a bolt down cover. All guarding should be kept efficient and in 

good condition. If the condition is poor, the guarding should be replaced before the implement is used. It is the operator’s 

responsibility to check the condition of the covers before each use.

UNLESS IT IS CORRECTLY PROTECTED THE TRANSMISSION COULD CAUSE DEATH SINCE IT CAN 

CATCH ON PARTS OF THE BODY OR CLOTHING

Driving Safely on Public Roads

Check the local Highway Code regulations before driving the tractor on public highways with an implement attached. 

Check the reflectors, hazard flashers and/or projecting load indicators are installed when required and efficient. These 

indicators must be installed correctly and easily seen by the drivers of other vehicles.

Bystanders must not be allowed to lean against or climb onto the machine during transport or while working. Do not 

allow bystanders to ride on the machine.

Maximum transport speed of the implement is limited to 25-30km/h depending on the model of the machine 

(observe safety labels on the machine).

General safety instructions

Precautions to be taken while working with the machine:

1. 

Do not operate the machine when you are tired or under the influence of alcohol or any other intoxicant;

2. Before starting mowing, make sure that the area is clear of people or animals.

3. It is mandatory to read all the safety requirements and the operator’s manual of the machine.

4. If you are not sure how to use the machine, please contact the manufacturer or the dealer.

Summary of Contents for MJ36-140

















































Reviews: