Majestic SA42R Page 4 Installation Manual Download

Page: 4 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

WARNING! Risk of Fire!

Vermont Casting Group dis-

claims any responsibility for, and the warranty and agency

listing will be voided by the following actions.

DO NOT:

• install or operate damaged fireplace

• modify fireplace

• install other than as instructed by Hearth & Home

Technologies

• operate the fireplace without fully assembling all

components

• overfire

• install any component not approved by Vermont Casting

Group

• install parts or components not Listed or approved
Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualified

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel

- Iron

- Brick

- Tile

- Concrete

- Slate

- Glass

- Plasters

• Materials reported as passing

ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood

- Compressed paper

- Plant fibers

- Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; flame proofed or

not, plastered or un-plastered

Product Specific & Important Safety Information

A. Fireplace Certification

This fireplace may be installed in sleeping rooms. This

fireplace is not approved for installation in manufactured

homes. If installed with a gas log set, provisions for the

National Fuel Gas Code must be met.
This fireplace is UL listed for use with SL300 series chim

ney system components.
This fireplace has been tested and listed for use with the

optional components specified in this manual. These op

tional components may be purchased separately and in

stalled at a later date. An outside air kit, gas insert, gas

log set or gas log-lighter should be installed at the time of

fireplace installation.

WARNING: This product and the fuels

used to operate this product (wood and

wood pellets), and the products of combus-

tion of such fuels, can expose you to chemi-

cals including carbon black, which is known

to the State of California to cause cancer

and carbon monoxide, which is known to

the State of California to cause birth defects

or other reproductive harm. For more infor-

mation go to: www. P65Warnings.ca.gov.

This fireplace system has been tested and listed in accor

dance with UL 127 and ULC-S610 standards by Underwrit

ers Laboratories Inc. for installation and operation in the

United States and Canada.

Summary of Contents for SA42R









































Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands

Majestic SA42R, Installation Manual

Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands