Majestic SA42R Page 29 Installation Manual Download

Page: 29 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

Noncombustible

Framing Material

HX4 or

equivalent

Figure 7.6 Raised Platform Hearth Extension-Framing

Non-combustible

Finishing Materials

Figure 7.7 Raised Platform Hearth Extension-Finishing

Floor

Noncombustible

Framing Material

Noncombustible

Finishing Material

Protective Metal

Hearth Strips

1/2 in. Micore

or equivalent

insulation

SA36R 16 in. Min

SA42R 20 in. Min

Hearth Extension

Note: The bottom of the fireplace

opening is 8-1/16 in. (205 mm)

above the bottom of the

fireplace. Finished hearth must

NOT extend above this level.

Figure 7.5 Raised Platform Hearth Extension Detail

1. Fireplace Installed Flush on the Floor and

Hearth Extension Raised to Bottom of Firebox

Opening

Non-combustible flooring a minimum of 16 in. (406 mm)

in front of and 8 in. (203 mm) to each side of fireplace

opening of the SA36R. 20 in. (508 mm) in front and 12

in. (305 mm) to each side of the SA42R is required.
The hearth framing must be constructed of non-com

bustible materials (such as metal framing or equivalent

material) and placed on HX3(s), HX4(s), or equivalent

material. See Figures 7.4 and 7.5.

When creating the platform, allow for the thickness

of the non-combustible finishing materials

Seal gaps between the hearth extension and the front

of the fireplace with a bead of non-combustible sealant

or grout.

2 in. (51 mm)

required

Floor constructed of wood or

other combustible material

Protective

Metal Hearth

Strip

1/2 in. Micore

or equivalent

insulation

Continuous,

non-combustible sealant

or grout

Tile, stone or other

non-combustible material

Note: Maximum height from floor under fireplace

to top of finished hearth extension is 8-1/16 in.

(205 mm).

Bottom of fireplace opening

Figure 7.4 Hearth Extension Construction

Vinyl Flooring is sensitive to heat. A 48 inch minimum

depth hearth extension is recommended when using
vinyl flooring up to the wall. See Figure 7.4.
Notice: Clearances that do not meet the minimum

guidelines could result in damage or buckling to the

vinyl flooring and is done at the installer’s risk.
Hearth and Home Technologies does not recommend

adhesive based vinyl flooring due to thermal expan

sion. Floating-style flooring can be used, but will reach

temperatures up to 110°F in a room with ambient tem

peratures of 70°F. Consult flooring specifications to

ensure compatibility.

Vinyl Flooring

Note: For installations

with vinyl flooring, special

clearance recommenda

tions apply.

►

Summary of Contents for SA42R









































Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands

Majestic SA42R, Installation Manual

Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands